Electrolux EI27EW35J S ユーザーズマニュアル
27" Combination Installation Specifications
•
Always consult local and national electric codes.
(Refer to product-specific electrical specifications on this page.)
(Refer to product-specific electrical specifications on this page.)
•
Minimum 23-5/8" deep cutout dimension is critical for proper
combination installation, to ensure that each built-in product’s faceplate
will fit flush against cabinet front.
combination installation, to ensure that each built-in product’s faceplate
will fit flush against cabinet front.
•
Bases must be level and cabinet front must be square.
•
Minimum 4-1/2" required distance from bottom of Warmer Drawer cutout
to floor.
to floor.
•
Respect critical dimensions as noted for proper installation of built-In
products.
products.
•
Minimum 21" clearance needed for Wall Oven door depth when open.
27" Built-In Microwave Specifications
•
Product Weight – 79 Lbs.
•
Voltage Rating – 120V / 60 Hz / 15 Amps
•
Connected Load (kW Rating) @ 120 Volts = 1.6 kW
(For use on adequately wired 120V, dedicated circuit having 2-wire
service with a separate ground wire. Appliance must be grounded
for safe operation.)
(For use on adequately wired 120V, dedicated circuit having 2-wire
service with a separate ground wire. Appliance must be grounded
for safe operation.)
•
Amps @ 120 Volts = 13.7 Amps
•
Full oven base of solid plywood or similar material required, capable of
supporting 150 Lbs.
supporting 150 Lbs.
•
Minimum 2-1/8" clearance required from bottom of Built-In Microwave
cutout to top edge of Wall Oven’s faceplate, leaving a 2" visible gap
between both product faceplates.
cutout to top edge of Wall Oven’s faceplate, leaving a 2" visible gap
between both product faceplates.
27" Electric Single Wall Oven Specifications
•
Product Weight – 150 Lbs.
•
Single phase 3- or 4-wire cable, 120 / 240 or 120 / 208 Volt, 60 Hertz
AC only electrical supply with ground required on separate circuit fused
on both sides of line.
AC only electrical supply with ground required on separate circuit fused
on both sides of line.
•
Connected Load (kW Rating) @ 240 / 208 Volts = 3.4 / 2.6 kW
•
Amps @ 240 / 208 Volts = 14.2 / 12.6 Amps
•
To support Wall Oven, two 3"-wide x 3/4"-thick planks must be installed
as a base, capable of supporting 150 Lbs. Do NOT use full base, since
planks are necessary to allow for proper air displacement.
as a base, capable of supporting 150 Lbs. Do NOT use full base, since
planks are necessary to allow for proper air displacement.
27" Warmer Drawer Specifications
•
Product Weight – 55 Lbs.
•
Voltage Rating – 120V / 450W / 60 Hz / 15 Amps
•
Connected Load (kW Rating) @ 120 Volts = 0.45 kW
(For use on adequately wired 120V, dedicated circuit having 2-wire
service with a separate ground wire. Appliance must be grounded
for safe operation.)
(For use on adequately wired 120V, dedicated circuit having 2-wire
service with a separate ground wire. Appliance must be grounded
for safe operation.)
•
Amps @ 120V = 3.75 Amps
•
Full base of solid plywood or similar material required, capable of
supporting 100 Lbs.
supporting 100 Lbs.
Note: For planning purposes only. Refer to Product Installation Guide
on the web at electroluxappliances.com for detailed instructions.
27" Combination Installation –
Built-In Microwave/Single Wall Oven/Warmer Drawer
High standards of quality at Electrolux Home Products, Inc. mean
we are constantly working to improve our products. We reserve the right
to change specifications or discontinue models without notice.
Electrolux Major Appliances, N.A.
USA
•
250 Bobby Jones Expressway
•
Augusta, GA 30907
•
1-877-4electrolux (1-877-435-3287)
•
electroluxappliances.com
CANADA
•
5855 Terry Fox Way
•
Mississauga, ON L5V 3E4
•
1-800-265-8352
•
electroluxappliances.ca
MODD_EW_WD 27INST EL 01/10
© 2010 Electrolux Major Appliances, NA
Printed in the U.S.A.
For detailed product dimensions
and installation specifications, refer
to model-specific product page and
installation guide on web
and installation specifications, refer
to model-specific product page and
installation guide on web
24" min.
3" max.
††
27
1
/
8
" min.
9
7
/
8
" min.
10
1
/
4
" max.
2"
min.
†
Full plywood base
required to support
100 lbs.
required to support
100 lbs.
27
1
/
4
" min.
27
5
/
8
" max.
24
7
/
8
" min.
25
1
/
4
" max.
Two 3" wide
by
by
3
/
4
" thick
planks must be
installed, capable
of supporting
150 lbs.
installed, capable
of supporting
150 lbs.
4"x 4" opening to route
armored cable
armored cable
25
1
/
2
" min.
25
3
/
4
" max.
4
1
/
2
" min.
required
23
5
/
8
" min.**
(critical
dimension)
Electrical junction
box location
box location
Bottom of
oven cutout
11
7
/
8
" min.**
(critical
dimension)
* Minimum 2
1
/
8
"
clearance required
from bottom of
Built-In Microwave
cutout to top edge of
Wall Oven’s faceplate,
leaving a 2" visible
gap between both
product faceplates.
from bottom of
Built-In Microwave
cutout to top edge of
Wall Oven’s faceplate,
leaving a 2" visible
gap between both
product faceplates.
** Critical dimension –
MUST be applied
†
Maximum height
depends on critical
dimension (11
depends on critical
dimension (11
7
/
8
")
††
Electrical junction
box for Wall Oven
must be lower than
the Warmer Drawer
cutout
box for Wall Oven
must be lower than
the Warmer Drawer
cutout
27" Warmer
Drawer Cutout
Drawer Cutout
For model:
EW27WD55G
EW27WD55G
2"
(visible
gap)*
27" Electric Single
Wall Oven Cutout
Wall Oven Cutout
For models:
EW27EW55G
EI27EW35J
EW27EW55G
EI27EW35J
27" Built-In
Microwave Cutout
Microwave Cutout
For model:
EW27MO55H
EW27MO55H
21" min.
21
1
/
2
" max.
25
1
/
8
" min.
25
5
/
8
" max.
Full plywood base
required to support
150 lbs.
required to support
150 lbs.
120V/60 Hz
grounded electrical
MUST be located
within shaded area
grounded electrical
MUST be located
within shaded area