ALTINEX MT115-111 ユーザーズマニュアル
MULTITASKER
400-0443-004
15
20. [SID+]
This command sets the card ID of all cards in a
system to their slot number plus the offset value.
system to their slot number plus the offset value.
Command Format: [SID+n]
n
= Offset amount (n = # from 0 to 99)
The maximum card ID is 99, so subtract
the highest slot number from 99 to find
the maximum offset. For example, in an
8-slot enclosure, the maximum offset
would be 91. The slot number (8) plus the
offset (91) equals 99.
the highest slot number from 99 to find
the maximum offset. For example, in an
8-slot enclosure, the maximum offset
would be 91. The slot number (8) plus the
offset (91) equals 99.
Example:
There are two 20-slot enclosures to be
connected together during normal operation.
The first unit will use the default IDs where the
card ID is equal to the slot number. The second
unit will have the same unit ID, but each card ID
will be offset by 20.
connected together during normal operation.
The first unit will use the default IDs where the
card ID is equal to the slot number. The second
unit will have the same unit ID, but each card ID
will be offset by 20.
Connect the computer to the second unit only
and send the command [SID+20] to set the ID of
all the cards in the second enclosure to their slot
number plus 20, then reconnect both units.
and send the command [SID+20] to set the ID of
all the cards in the second enclosure to their slot
number plus 20, then reconnect both units.
The cards in the first unit will be referenced as
card IDs 1-20 and the cards in the second unit
will be referenced by card IDs 21-40.
card IDs 1-20 and the cards in the second unit
will be referenced by card IDs 21-40.
21. [RSN]
This command displays the slot number of a
card with a specified ID number. If more than
one card has the same ID, each slot number will
be displayed.
card with a specified ID number. If more than
one card has the same ID, each slot number will
be displayed.
Command Format: [RSNCi]
Ci
= Card ID (i = # from 1 to 99)
Example:
The card in slot 4 takes up four slots in the
enclosure. Its ID was set to 1 since it is the first
card installed in the system, reading from left to
right. Send the command [RSNC1] to find the
slot number of this card. The system responds
with the following feedback:
enclosure. Its ID was set to 1 since it is the first
card installed in the system, reading from left to
right. Send the command [RSNC1] to find the
slot number of this card. The system responds
with the following feedback:
[4]
GROUP COMMANDS
Group commands allow several cards with the
same functions to be controlled simultaneously with
a single command. Up to 8 groups (G1-G8) may be
defined. These commands apply to all cards, not
only the MT115-111.
same functions to be controlled simultaneously with
a single command. Up to 8 groups (G1-G8) may be
defined. These commands apply to all cards, not
only the MT115-111.
22. [WR]
This command adds cards to a group. In
MultiTasker systems with audio and video cards,
the groups are typically as follows:
MultiTasker systems with audio and video cards,
the groups are typically as follows:
Group 1 = Video Cards
Group 2 = Audio Cards
Group 3 = Video and Audio Cards
Command Format: [WRCn
1
Cn
2
…Gk]
Cn = Card ID (n = slot # from 1 to max slots)
Gk = Group ID (k = # from 1-8)
Example:
Add C2, C4, and C6 to G5 by sending the
command [WRC2C4C6G5]. After executing this
command, G5 will consist of C2, C4, and C6.
command [WRC2C4C6G5]. After executing this
command, G5 will consist of C2, C4, and C6.
Now add C8 to G5 by sending [WRC8G5]. C8 is
added to G5, and G5 is not overwritten. View
the contents of G5 by sending [RDG5] and
receiving the following feedback:
added to G5, and G5 is not overwritten. View
the contents of G5 by sending [RDG5] and
receiving the following feedback:
[G5=C2C4C6C8]
23. [RMC]
This command removes one or more cards from
a group.
a group.
Command Format: [RMCn
1
Cn
2
…Gk]
Cn = Card ID (n= # from 1 to max slots)
Gk = Group ID (k = # from 1-8)
Example:
G5 consists of C2, C4, C6, and C8. Remove C6
and C8 by sending [RMC6C8G5]. View the
contents of G5 by sending [RDG5] and receiving
the following feedback:
and C8 by sending [RMC6C8G5]. View the
contents of G5 by sending [RDG5] and receiving
the following feedback:
[G5=C2C4]