Regency L676-NG1 ユーザーズマニュアル

Regency

®

 L676-1 Direct Vent Gas Fireplace

INST

ALLA

TION

1)  Clocking the appliance to ensure the correct 

fi ring rate (rate noted on label 33,000 (NG)

    - High Altitude 32,000 (NG) Btu/h, 31,500 

(LP) Btu/h after burning appliance for 15 
minutes.

2)  If required, adjusting the primary air to ensure 

that the fl ame does not carbon.  First allow 
the unit to burn for 15-20 min. to stabilize.

1)  Ensure that structural members are not cut 

or weakened during installation.

2)  Ensure proper grounding using the #8 

ground lug provided. See "Wiring Diagram" 
section.

1)  When selecting a location for your fi replace, 

ensure that the clearances are met.

2)  The appliance must be installed on a fl at, 

solid, continuous surface (e.g. wood, metal, 
concrete). This may be the fl oor, or raised up 
on a platform to enhance its visual impact. 
The appliance must be installed on a metal 
or wood panel extending the full width and 
depth of the appliance.

3)  The L676-1 Direct Vent Gas Fireplace can 

be installed in a recessed position or framed 
out into the room as in A, B, C and D. See 

D) Corner
4)  This appliance is Listed for bedroom  

installations using the standard Remote 
(millivolt thermostat system). Some areas 
may have further requirements, check local 
codes before installation.

5)  The L676-1 Direct Vent Gas Fireplace 

is approved for alcove installations, see 
"Clearances" section for details.

6)  We  recommend that you plan your installation 

on paper using exact measurements for 
clearances and floor protection before 
actually installing this appliance. Have an 
authorized inspector, dealer, or installer 
review your plans before installation.

The  HeatWave Air Duct Kit increases the 
effectiveness of your fi replace by dispersing warm 
air from the fi replace to remote locations in the 
same room or other rooms in your home.

Up to  two kits may be installed on the fi replace. 
Please Note: Only 1 HeatWave kit may be 
operated at one time. 

See HeatWave installation manual for complete 
details and clearances from side only.

Diagram 1.

A)  Flat on Wall
B)  Flat on Wall Corner
C) Recessed 

into 

 Wall/Alcove

The Heat  Release Kit expels warm air from the 
fi replace to the outside of the building, allowing 
the fi replace to be operated with less heat entering 
the room. The kit may be used on either the left 
or right side.

See Heat Release installation manual for complete 
details and clearances from side only.

9)  Test Gas Pressure (Refer to "Gas Pipe Pres-

sure Testing" section).

10) Install standard and optional features.  Refer 

to the following sections: 

 a)  Brick 

Panels

 b)  Log 

Set

 

c) 

Remote Control - refer to "Matching  

 

Remote Handset & Control Box  

 

ID Code" section.

11) Final check.

Before leaving this unit with the customer, the 
installer must ensure that the appliance is fi ring 
correctly and operation fully explained to 
customer.

The  HeatWave Duct Kit has different 
clearance and framing requirements, 
check the HeatWave manual for details.

The maximum height that combustible fl oor can 
be brought above the base of the unit is 3".

Combustible material can only be installed to 
the bottom lip of the fi replace as shown below.  
The fi nished fl oor must not come in contact with 
the front face of the fi replace. Non-combustible 
material (see "Framing and Finishing" section) 
must act as a barrier between the front face and 
fi nished fl oor.