Pella 81CM0100 ユーザーズマニュアル
If products cannot be finished immediately, cover with clear plastic to protect from dirt, damage and moisture.
Remove any construction residue before finishing. Sand all wood surfaces lightly with 180 grit or finer sandpaper.
DO NOT use steel wool. BE CAREFUL NOT TO SCRATCH THE GLASS. Remove sanding dust.
Remove any construction residue before finishing. Sand all wood surfaces lightly with 180 grit or finer sandpaper.
DO NOT use steel wool. BE CAREFUL NOT TO SCRATCH THE GLASS. Remove sanding dust.
Pella products must be finished per the below instructions; failure to follow these instructions voids the Limited
Warranty.
Warranty.
Ř2QSDWLRGRRUVLWLVRSWLRQDOWRSDLQWVWDLQRUŵQLVKWKHYHUWLFDODQGKRUL]RQWDOSDQHOHGJHV
Note: To maintain proper product performance do not paint, finish or remove the weather-stripping, mohair
dust pads, gaskets or vinyl parts. Air and water leakage will result if these parts are removed. After finishing,
allow venting windows and doors to dry completely before closing them.
dust pads, gaskets or vinyl parts. Air and water leakage will result if these parts are removed. After finishing,
allow venting windows and doors to dry completely before closing them.
Pella Corporation is not responsible for interior paint and stain finish imperfections for any product that is not
factory-applied by Pella Corporation. Use of inappropriate finishes, solvents, brickwash, or cleaning chemicals will
cause adverse reactions with the window and door materials and voids the Limited Warranty.
factory-applied by Pella Corporation. Use of inappropriate finishes, solvents, brickwash, or cleaning chemicals will
cause adverse reactions with the window and door materials and voids the Limited Warranty.
For additional information on finishing see Pella Owner’s Manual or go to www.pella.com.
INTERIOR FINISH
Care and maintenance information is available by contacting your local Pella retailer. This
information is also available at www.pella.com.
information is also available at www.pella.com.
CARE AND MAINTENANCE
Because all construction must anticipate some water infiltration, it is important that the wall system be designed
and constructed to properly manage moisture. Pella Corporation is not responsible for claims or damages
caused by anticipated and unanticipated water infiltration; deficiencies in building design, construction and
maintenance; failure to install Pella
and constructed to properly manage moisture. Pella Corporation is not responsible for claims or damages
caused by anticipated and unanticipated water infiltration; deficiencies in building design, construction and
maintenance; failure to install Pella
®
products in accordance with Pella installation instructions; or the use of Pella
products in wall systems which do not allow for proper management of moisture within the wall systems. The
determination of the suitability of all building components, including the use of Pella products, as well as the
design and installation of flashing and sealing systems are the responsibility of the Buyer or User, the architect,
contractor, installer, or other construction professional and are not the responsibility of Pella.
determination of the suitability of all building components, including the use of Pella products, as well as the
design and installation of flashing and sealing systems are the responsibility of the Buyer or User, the architect,
contractor, installer, or other construction professional and are not the responsibility of Pella.
Pella products should not be used in barrier wall systems which do not allow for proper management of moisture
within the wall systems, such as barrier Exterior Insulation and Finish Systems, (EIFS) (also known as synthetic
stucco) or other non-water managed systems. Except in the states of California, New Mexico, Arizona, Nevada,
Utah, and Colorado, Pella makes no warranty of any kind and assumes no responsibility for Pella windows
and doors installed in barrier wall systems. In the states listed above, the installation of Pella products in
barrier wall or similar systems must be in accordance with Pella installation instructions.
within the wall systems, such as barrier Exterior Insulation and Finish Systems, (EIFS) (also known as synthetic
stucco) or other non-water managed systems. Except in the states of California, New Mexico, Arizona, Nevada,
Utah, and Colorado, Pella makes no warranty of any kind and assumes no responsibility for Pella windows
and doors installed in barrier wall systems. In the states listed above, the installation of Pella products in
barrier wall or similar systems must be in accordance with Pella installation instructions.
Product modifications that not approved by Pella Corporation will void the Limited Warranty.
IMPORTANT NOTICE