Beko DCY 7202 XW3 ユーザーズマニュアル
27 / 28 EN
Dryer / User Manual
Make sure that you have an earthed power outlet
socket rated at 13 amps (minimum).
socket rated at 13 amps (minimum).
Attention!
If you use your dryer as built-in, the socket must
be reachable after installation, or a separate
switch (which can disconnect the two poles) must
be used in the installation. Check for suitability.
For a permanent connection, a master switch with
at least 3mm contact clearance and minumum 13
A rating must be used.
be reachable after installation, or a separate
switch (which can disconnect the two poles) must
be used in the installation. Check for suitability.
For a permanent connection, a master switch with
at least 3mm contact clearance and minumum 13
A rating must be used.
Electrical requirements
Before you insert the plug into the wall socket
make sure that the voltage and the frequency
shown in the rating label corresponds to your
electricity supply.
We recommend that this appliance be connected
to the mains supply via a suitable switched and
fused socket in a readily accessible position.
Should the mains lead of the appliance become
damaged or need replacing at any time, it must
be replaced by a special purpose made mains
lead which can only be obtained from a Authorised
Service Agent.
A Warning
This appliance must be earthed
If the fitted moulded plug is not suitable for your
socket, then the plug should be cut off and an
appropriate plug fitted.
The moulded plug on this appliance incorporates a
13A fuse. Should the fuse need to be replaced an
ASTA approved BS1362 fuse of the same rating
must be used. Do not forget to refit the fuse cover.
In the event of losing the fuse cover, the plug must
not be used until a replacement fuse cover has
been fitted. Colour of the replacement fuse cover
must be the same colour as that visible on the pin
face of the plug. Fuse covers are available from
any good electrical store.
In order to avoid hazards, damaged supply cord
should be replaced by the manufacturer, its service
agent or similarly qualified people.
make sure that the voltage and the frequency
shown in the rating label corresponds to your
electricity supply.
We recommend that this appliance be connected
to the mains supply via a suitable switched and
fused socket in a readily accessible position.
Should the mains lead of the appliance become
damaged or need replacing at any time, it must
be replaced by a special purpose made mains
lead which can only be obtained from a Authorised
Service Agent.
A Warning
This appliance must be earthed
If the fitted moulded plug is not suitable for your
socket, then the plug should be cut off and an
appropriate plug fitted.
The moulded plug on this appliance incorporates a
13A fuse. Should the fuse need to be replaced an
ASTA approved BS1362 fuse of the same rating
must be used. Do not forget to refit the fuse cover.
In the event of losing the fuse cover, the plug must
not be used until a replacement fuse cover has
been fitted. Colour of the replacement fuse cover
must be the same colour as that visible on the pin
face of the plug. Fuse covers are available from
any good electrical store.
In order to avoid hazards, damaged supply cord
should be replaced by the manufacturer, its service
agent or similarly qualified people.
A
Important
Fitting a different plug
As the colours of the wires in the mains lead
of this appliance may not correspond with the
coloured markings identifying the terminals on
your plug, proceed as follows:
1 Connect the green - yellow or green (earth) wire
to the terminal in the plug marked ‘E’ or with the
symbol or coloured green and yellow or green.
2 Connect the blue (neutral) wire to the terminal in
the plug marked ‘N’ or coloured black.
3 Connect the brown (live) wire to the terminal in
the plug marked ‘L’ or coloured red.
With the alternative plugs a 13A fuse must be
fitted either in the plug or adaptor or in the main
fuse box. If in doubt contact a qualified electrician.
As the colours of the wires in the mains lead
of this appliance may not correspond with the
coloured markings identifying the terminals on
your plug, proceed as follows:
1 Connect the green - yellow or green (earth) wire
to the terminal in the plug marked ‘E’ or with the
symbol or coloured green and yellow or green.
2 Connect the blue (neutral) wire to the terminal in
the plug marked ‘N’ or coloured black.
3 Connect the brown (live) wire to the terminal in
the plug marked ‘L’ or coloured red.
With the alternative plugs a 13A fuse must be
fitted either in the plug or adaptor or in the main
fuse box. If in doubt contact a qualified electrician.
Green and yellow
or green
N
Blue or black
L
Brown or red
8
Electrical Connection