Cobra Electronics PR255-2VP-C ユーザーズマニュアル
Customer Assistance
Warranty
Introduction
O
Op
pe
erra
attiio
on
n
Communicating with Another Person
••
To talk to another person:
1. Press and hold the Talk button.
2. With the microphone about two inches
1. Press and hold the Talk button.
2. With the microphone about two inches
(five cm) from your mouth, speak in a
normal voice.
normal voice.
3. Release the Talk button when you are
finished talking and listen for a response.
You cannot receive incoming calls while
pressing the Talk button.
pressing the Talk button.
Both radios must be tuned to the
same channel to communicate.
same channel to communicate.
Channels
••
To select a channel:
– With the radio on, select any of the
– With the radio on, select any of the
22 channels by pressing the Channel Up
or Channel Down button.
or Channel Down button.
Both radios must be tuned to the
same channel to communicate.
same channel to communicate.
Channels 1 through 7 are shared with FRS/
GMRS. Channels 8 through 14 are FRS only.
Channels 15 through 22 are GMRS only.
GMRS. Channels 8 through 14 are FRS only.
Channels 15 through 22 are GMRS only.
See page 14 for FRS/GMRS frequency
allocations and compatibility charts.
allocations and compatibility charts.
C
Ch
ha
an
nn
ne
ell B
Bu
utttto
on
n
C
Ch
ha
an
nn
ne
ell N
Nu
um
mb
be
err
T
Ta
allk
k B
Bu
utttto
on
n
T
Tw
wo
o IIn
nc
ch
he
es
s ((ffiiv
ve
e
c
cm
m)) ffrro
om
m M
Mo
ou
utth
h
E
En
ng
glliis
sh
h
2
2
Turning on Your microTALK
®
Radio
••
To turn on your radio:
– Press and hold the Mode/Power button until
– Press and hold the Mode/Power button until
you hear a series of audible tones indicating
the radio is on.
the radio is on.
Your microTALK
®
radio is now in Standby mode,
ready to receive transmissions. The radio is
always in Standby mode except when the Talk,
Call or Mode/Power buttons are pressed.
always in Standby mode except when the Talk,
Call or Mode/Power buttons are pressed.
Battery Low
••
When battery power is low, the Battery Low icon
will blink. Your batteries should be replaced or
recharged, if using rechargeable batteries.
will blink. Your batteries should be replaced or
recharged, if using rechargeable batteries.
Auto Battery Save
••
Your microTALK
®
radio has a unique circuit
designed to extend battery life. If there are no
transmissions within 10 seconds, the radio will
automatically switch to Battery Save mode and
the Power Saver icon will flash in the display.
This will not affect the radio’s ability to receive
incoming transmissions.
transmissions within 10 seconds, the radio will
automatically switch to Battery Save mode and
the Power Saver icon will flash in the display.
This will not affect the radio’s ability to receive
incoming transmissions.
U
Us
siin
ng
g Y
Yo
ou
urr R
Ra
ad
diio
o
O
Op
pe
erra
attiio
on
n
M
Mo
od
de
e//P
Po
ow
we
err B
Bu
utttto
on
n
B
Ba
atttte
erry
y L
Lo
ow
w
B
Ba
atttte
erry
y S
Sa
av
ve
e M
Mo
od
de
e
3
3
N
No
otth
hiin
ng
g Comes Close to a Cobra
®
The Basics to Get You Started
Your microTALK
®
radio is easy to use.
To get started, simply:
1. Press and hold the Mode/Power button
1. Press and hold the Mode/Power button
to turn on your radio.
2. Press the Channel Up or Channel Down
button to select a channel.
Both radios must be tuned to the
same channel to communicate.
same channel to communicate.
3. Press and hold the Talk button while
speaking into the microphone.
4. When finished talking, release the Talk
button and listen for a response.
9627-PR255-2VP-C English-1 3/29/06 3:32 PM Page 2