Vision Fitness R2750HRT ユーザーズマニュアル

• Slide the console mast boot onto the 
console mast.

• Unfold the wire harness and heart
rate wires located in the console mast
frame bracket. Attach the wire tie
coming from the bottom of the console
mast to the wire harness and heart
rate wires. Pull the wire tie with wire
harness and heart rate wires up
through the top of the console mast
while simultaneously sliding the mast
into the frame bracket.

• Secure the console mast to the
frame bracket with six bolts (M8x15L).
Tighten with the 5mm T-Shaped
wrench. Insert a set screw (M10x12L) to
the front edge of the mast and tighten
until snug with the 5mm T-shaped
wrench.

• Slide the console mast boot down
and snap it into place on the side cover.

• Mount the upper handlebars to the
console mast using two lock washers
(M8) and two bolts (M8x15L). Tighten
with the 5mm T-Shaped wrench.

• Remove the four mounting screws from
the back of the console. Connect the
wire harness and heart rate wires that
come from the console mast into the
plugs located in the back of the console.
Attach the console to the mast with the
four screws removed earlier.

• Remove the battery cover on the back
side of the console. Plug in the 9-volt
battery. Re-attach the battery cover.

• Install the rear foot with the four
lock washers (M8), two inside bolts
(M8x65L), and two outside bolts
(M8x20L). Tighten with the 5mm 
T-Shaped wrench.

COMMERCIAL FITNESS BIKES

• Remove the two socket head bolts
from the sliding seat adjustment bracket.
Slide the seat adjustment handle
between the teeth of the seat adjustment
bracket. Re-insert the two socket head
bolts and tighten with the 4mm L-
shaped wrench.

• Attach the seat frame to the sliding
seat bracket using four lock washers
(M8) and four bolts (M8x20L) and the
5mm T-Shaped wrench.

• Connect Wires A on the seat 
handlebar to Wires B on the sliding
seat bracket. Connect the wire harness
coming from the seat frame to the wire
harness in the handlebars. Attach the
seat handlebars to the sliding seat
bracket using four lock washers (M8)
and four bolts (M8x20L). Tighten with
the 5mm T-Shaped wrench.

To avoid possible damage to this Fitness Bike, please follow these assembly steps in the correct order.
Before proceeding, find your new Fitness Bike’s serial number located on the front axle tube, and enter here:

Refer to this number when calling for service, and enter this serial number on your Warranty Card and in
your own records. Be sure to read your Owner’s Guide before using your new Fitness Bike.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12

NOTE:

It is recommended that you apply grease to the threads of each bolt and screw as you assemble

your Fitness Bike to prevent loosening and noise. Also, during each assembly step, ensure that ALL screws
and bolts are in place and partially threaded in before completely tightening any ONE screw or bolt.

• Mount the seat bottom to the seat
frame with four bolts (M6x55L) and
four lock washers (M6). Tighten with
the 4mm L-shaped wrench.

• Attach the left and right pedals to
the left and right crank arms. Tighten
the pedals using the 15mm Pedal
Wrench.

• Secure the Accessory Tray to the
seat handlebar with two bolts
(M5x35L) and two lock washers
(M5). Be careful when inserting the
bolts to clear the wires inside the 
handlebar to prevent damage.
Tighten with the screwdriver.