Vision Fitness R2150 プリント

• Slide the console mast cover onto

the console mast.

• T

ake the wire tie that exits the

bottom of the console mast and wrap

it around the wire har

ness and hear

t

rate wires that are sitting in the

console mast bracket on the frame.

Pull the wire tie up through the top of

the console mast so that the wire

har

ness and hear

t rate wires exit the

top of the mast.

• Slide the bottom of the console mast

over the frame bracket being careful

not to pinch the hear

t rate wires or

wire har

ness. Assure the mast is

positioned correctly by inser

ting the

Set Screw (M8x10L) through the front

edge of the mast. T

ighten with the

5mm T

-handle wrench. Secure the

mast to the frame with four bolts

(M8x15L) and four lock washers (SW8).

Tighten with the 5mm T

-handle wrench.

• Slide the console mast cover down

so it sits on the frame covers.

• Mount the console mast handlebar

to the console mast with two bolts

(M8x20L) and two lock washers (SW8).

Tighten with the 5mm T

-handle wrench.

• With the screwdriver remove the

four bolts on the back side of the

console. Plug in the wire har

ness and

hear

t rate wires to the back side of the

console. Mount the console to the

console mast with the four bolts and

screwdriver

.

• Remove the water bottle cage bolts

from the backside of the console mast.

Mount the water bottle cage to the

mast with these two bolts and the

screwdriver

.

• Attach the left and right pedals to

the left and right crank ar

ms. 

both pedals and crank ar

ms should

be labeled left or right. T

ighten with

the included pedal wrench.

•

 Plug in the power supply to the power

socket on the front side of the bike.

•

 Slide the Rear Foot into place on the

back end of the frame. Secure the foot

in place to the frame with two bolts

(M8x20L) and two lock washers (SW8)

to the outside holes and with two bolts

(M8x65L) and two lock washers (SW8)

to the inside holes. T

ighten with the

5mm T

-Handle W

rench.

• Attach each half of the rear foot joint

cover with the M4x10L screw

. T

ighten

with the screwdriver

.

To

 avoid possible damage to this Fitness Bike, please follow these assembly steps in the correct order

.

Before proceeding, find your new Fitness Bike’

s serial number located on the front axle tube, and enter

here:

Refer to this number when calling for ser

vice, and enter this serial number on your W

arranty Card and in

your own records. Be sure to read your Owner’

s Guide before using your new Fitness Bike.

If any par

ts, hardware or tools are missing, please call 1.800.335.4348, Extension 12

NOTE:

It is recommended that you apply grease to the threads of each bolt and screw as you assemble

your Fitness Bike to prevent loosening and noise. Also, during each assembly step, ensure that ALL bolts

and screws are in place and par

tially threaded in before completely tightening any ONE bolt or screw

.

AND

STEP-THRU SEMI-RECUMBENT FITNESS BIKES

• Rotate the handle on the seat frame to

the for

ward most position. T

ighten the

adjustment bolt on the seat frame

bracket with the 5mm T

-Shaped wrench.

• Slide the seat frame onto the seat rail.

Attach the seat rail stopper onto the seat

rail with two (M8x25L) bolts and two

lock washers (SW8). T

ighten with the

5mm T

-handle wrench.

• Connect the hear

t rate wires in the

seat handlebar to the hear

t rate wires

coming up from the seat frame.

• Mount the seat handlebars to the seat

frame with four bolts (M8x15L) and four

lock washers (SW8).  T

ighten with the

5mm T

-Handle wrench.

• Mount the seat bottom cushion to the

seat frame with four bolts (M6x35L) and

four arc washers (M6). T

ighten with the

4mm L-shaped wrench.  

• Mount the seatback cushion to the

seat frame with four bolts (M6x35L) and

four arc washers (M6). T

ighten with the

4mm L-shaped wrench.