Vision Fitness X1500 ユーザーズマニュアル

To avoid possible damage to this Elliptical Trainer, please follow these assembly steps in the correct order.
Before proceeding, find your new Elliptical Trainer’s serial number located on the front axle tube, and enter
here:

Refer to this number when calling for service, and enter this serial number on your Warranty Card and in
your own records. Be sure to read your Owner’s Guide before using your new Elliptical Trainer.
If any parts, hardware or tools are missing, please call 1.800.335.4348

NOTE:

It is recommended that you apply grease to the threads of each bolt and screw as you assemble your

Elliptical Trainer to prevent loosening and noise. Also, during each assembly step, ensure that ALL bolts and
screws are in place and partially threaded in before completely tightening any ONE bolt or screw.

ELLIPTICAL TRAINER

• Slide a wavy washer (25x34x2T) on
to the right rotation axle. Slide the 
knuckle joint of the pedal arm assembly
onto the right rotation axle. The pedal
arm roller wheel should be placed into
the groove of the guide rail. Secure the
pedal arm assembly to the rotation axle
with a washer (8x38x2T) and bolt
(M8x20L). Tighten with the 5mm T-
shaped wrench.

• Place the pedal arm cover over the
knuckle joint. Secure in place with a
washer (4x10x1T) and bolt (M4x12L).
Tighten with the screwdriver.

• Repeat both steps on the left side.

• Slide the boot onto the console mast.

• Unfold the wire harness located in
the frame bracket. Wrap the end of
the wire tie, located at the bottom of
the console mast, around the end of
the wire harness. Pull the wire tie and
wire harness up through the console
mast while simultaneously sliding the
mast over the frame bracket. 

• Slide a lock washer (SW8)
followed by a flat washer (8x18x1T)
onto four of the bolts (M8x15L).  Insert
these bolts through the side of the mast
to secure the mast to the frame. Slide
a lock washer (SW8) followed by a
arc washer (8x17x1T) onto the two
remaining bolts (M8x15L). Insert these
bolts through the holes in front of the
mast. Tighten all bolts with the 5mm 
T-shaped wrench.

• Slide the boot down the console mast
and set it in place over the side covers.

• Remove the four bolts from the back
of the console. Connect the wire
harness to the plug in the back of the
console. Connect the heart rate wires
into the heart rate plugs in the back of
the console. Attach the console to the
console mast with the four console
bolts and screwdriver.

• Attach the water bottle cage to the
console mast with the two bolts
located on the mast.

• Slide the dual-action axle cover into
place over the console mast axle.
Slide a wavy washer (25x34x2T)
onto the console mast axle. Slide the
right dual-action arm onto the axle. Fix
in place with a washer (8x38x2T)
and nylon nut (M8). Cover with the
included nylon nut cover.

• Insert the link joint sleeve (SS41)
into the socket joint of the right link
arm. Position the socket joint of the
link arm into the bracket at the bottom
of the dual-action arm. Position the
Nylon Interval Rings between the
socket joint and bracket on each side.
Insert a bolt (M8x45L) through the
bracket, interval rings and socket joint
sleeve. Secure in place with a washer
(8x25x1.5T) and nylon nut (M8).
Tighten with the 5mm T-shaped
wrench and 13mm wrench.

• Position the link arm covers over the
socket joint and secure the two pieces
together with a screw (M4x12L).
Tighten with the screwdriver. Connect
the cover to each side of the link arm
with a washer (5x10x1T) and bolt
(M5x12L). Tighten with the 
screwdriver.

• Position the right footplate onto the
right link arm. Secure in place with
four washers (6x14x1T) and four bolts
(M5x12L). Tighten with the screwdriver. 

• Repeat steps on the left side.

• Attach the hand grips onto the dual-
action arms by turning grip in a
clockwise direction. Make sure it is tight.

• Slide the stabilizer shaft through the
plastic sleeves in the rear support tube.

NOTE: A tight fit between the shaft
and sleeves is important to the stability
of the unit. Because of this, it may be
helpful to tap the shaft through with a
rubber mallet.

• Slide the stabilizer covers onto the
stabilizer shaft and secure with
(M8x20L) bolts and (8x16x1T) flat
washers. Tighten with the 5mm 
T-shaped wrench.

• Attach end caps to the end of the
guide rails with (M8x15L) bolts. Tighten
with the 5mm T-shaped wrench.

• Refer to Product Selection and
Model Configuration

decal on

console or follow these steps.

• Once the product is plugged in turn
on the console

• Select product (Bike (BK) or Elliptical
(EP)) using the resistance arrow keys.
Press ENTER to select.

• Select model number (Bike (1500,
2050, 2250, 3200) or Elliptical
(1500, 6000, 6200)) using the
RESISTANCE arrow keys. Press
ENTER to select. Console will reset to
start-up screen.

• The product selection and model
configuration is now complete.