Vision Fitness X6200 ユーザーズマニュアル

• Slide a wavy washer (25x34x2T)
onto the right rotation axle. Slide the
bushing housing of the right pedal
arm onto the right rotation axle. The
pedal arm roller wheel should be
placed in the groove of the guide rail.
Secure the pedal arm to the rotation
axle with a washer (8x38x2.0T) and
bolt (M8x20L). Tighten with a 5mm 
T-shaped wrench.

• Place the pedal arm bracket cover
over the bushing housing of the pedal
arm. Secure in place with a washer
(5x10x1T) and bolt (M5x10L).
Tighten with the screwdriver.

• Repeat both steps on the left side.

To avoid possible damage to this Elliptical Trainer, please follow these assembly steps in the correct order.
Before proceeding, find your new Elliptical Trainer’s serial number located on the front axle tube, and enter
here:

Refer to this number when calling for service, and enter this serial number on your Warranty Card and in
your own records. Be sure to read your Owner’s Guide before using your new Elliptical Trainer.
If any parts, hardware or tools are missing, please call 1.800.335.4348

NOTE:

It is recommended that you apply grease to the threads of each screw as you assemble your Elliptical

Trainer to prevent loosening and noise. Also, during each assembly step, ensure that ALL screws are in
place and partially threaded in before completely tightening any ONE screw.

FOLDING ELLIPTICAL TRAINER

• On the right side, slide the dual- action
axle cover into place on the console
mast axle. Slide a wavy washer
(25x34x2T) onto the axle. Slide the right
dual-action arm on the axle. Fix in place
with the washer (8x38x2T) and locknut
(M8). Cover with the included nut cap.

• Make sure the sleeve is in place in the
socket joint of the lower link arm.
Connect the lower link arm to the dual
action arm with a bolt (M8x30L). Attach
the washer (8x25x1.5T) and nut (M8) to
the end of the bolt. Tighten with the 5mm
L-Shaped wrench and 13mm wrench.

• Position the link arm cover over the
joint of the lower link arm and secure the
two pieces of the cover together with a
panhead bolt (M4x15L). Connect the
cover to each side of the lower link arm
with a washer (5x10x1T) and bolt
(M5x12L).

• Set multi-position grip on the dual-
action arm. Secure with two washers
(6x12x1.0T) and two bolts (M6x15L).
Tighten with the 4mm L-shaped wrench.

• Repeat these steps on the left side.

• Slide a wavy washer (20x29x1.5T)
on the lower link arm axle, which is
located under the foot plate. Slide the
axle through the bracket located on
top of the pedal arm. 

• Secure the lower link arm to the
pedal arm by attaching the pedal 
support bracket with three bolts
(M8x13L). Tighten with the 5mm 
T-shaped wrench.

• Repeat this step on opposite side.

• Place a piece of packaging under
the front of the unit to aid in assembly.

• Secure the front stabilizer to the
base frame plate with four bolts
(M8x25L) and four arc washers
(8x17x1.0T). Tighten with the 5mm
L-shaped wrench.

• Place a piece of packaging under
the front of the unit to aid in assembly.

• Slide the axle through the plastic
sleeve of the frame. Slide a washer
(17x40x1.0T) onto each side of the
axle. Slide the left guide rail onto the
left side of the axle and the right guide
rail onto the right side of the axle.

• Slide the right stabilizer onto the
right side of the axle and the left
stabilizer onto the left side of the axle.
Fix each side in place with a washer
(8x14x1T) and bolt (M8x20L).
Tighten with a 5mm T-shaped wrench.

• Slide the boot onto the console mast.

• Unfold the wire harness located in the
frame bracket. Wrap the wire tie around
the end of the wire harness. Pull the wire
tie and wire harness up through the top
of the console mast while simultaneously
sliding the mast into the frame bracket.

• Secure the mast to the frame using
three lock washers (8x15x2T) and three
bolts (M8x60L). Tighten with the 6mm 
L-Shaped wrench.

• Slide the boot down the console
mast and snap it in place on top of
the side cover.

• Remove the four screws from the
back of the console. Connect the wire
harness to the plug in the back of the
console. Connect the heart rate wires
from the console mast to the console.
Attach the console to the console mast
with the four screws.

• Attach the water bottle cage with the
screwdriver and the screws located in
the console mast.

• Refer to Product Selection and
Model Configuration

decal on

console or follow these steps.

• Once the product is plugged in turn
on the console

• Select product (Bike (BK) or Elliptical
(EP)) using the resistance arrow keys.
Press ENTER to select.

• Select model number (Bike (1500,
2050, 2250, 3200) or Elliptical
(1500, 6000, 6200)) using the
RESISTANCE arrow keys. Press
ENTER to select. Console will reset to
start-up screen.

• The product selection and model
configuration is now complete.