Vision Fitness E1500 ユーザーズマニュアル

• Slide the rear foot into place on the
frame. Insert two bolts (M8x25L) with
two lock washers (SW8) to the outside
holes. Insert two bolts (M8x70L) with
two lock washers (SW8) to the inside
holes. Tighten all bolts with the 5mm 
T-Shaped wrench.

To avoid possible damage to this Fitness Bike, please follow these assembly steps in the correct order. Before
proceeding, find your new Fitness Bike’s serial number located on the front axle tube, and enter here:

Refer to this number when calling for service, and enter this serial number on your Warranty Card and in
your own records. Be sure to read your Owner’s Guide before using your new Fitness Bike.
If any parts, hardware or tools are missing, please call 1.800.335.4348

NOTE:

It is recommended that you apply grease to the threads of each bolt and screw as you assemble

your Fitness Bike to prevent loosening and noise. Also, during each assembly step, ensure that ALL bolts
and screws are in place and partially threaded in before completely tightening any ONE bolt or screw.

UPRIGHT FITNESS BIKE

• Slide the console mast cover onto the
console mast.

• Wrap the wire tie that exits the
bottom of the console mast around the
end of the console cable that is resting
in the console mast mounting bracket.
Pull the wire tie with the wire harness up
through the console mast. Slide the
console mast over the console mast
mounting bracket. Insert three bolts
(M8x15L) with three lock washers
(SW8) to each side of the mast. Insert a
set screw (M8x10L) to the front side of
the mast and tighten with the 4mm 
L-Shaped wrench. Tighten all other bolts
with the 5mm T-Shaped wrench. Slide
the console mast cover down so that it
sits in place on the bike.

• Slide the heart rate wires from the
handlebar through the hole in the
handlebar mounting bracket on the
console mast. Pull the wires completely
through the hole and set the handlebars
into place on the bracket. Secure the
handlebars in place with the two bolts
(M8x20L) and two lock washers
(SW8). Tighten with the 5mm T-Shaped
wrench.

• Remove the four bolts from the back
side of the console. Plug the console
cable and heart rate wires into the back
side of the console. Place the console
onto the mounting plate of the console
mast and re-insert the four mounting
bolt. Tighten with the screwdriver.

• Remove the two bolts from the
backside of the console mast. Attach
the water bottle cage to the mast with
these two bolts. Tighten with the
screwdriver. Insert water bottle.

• Position the front support tube in place
under the mounting plate on the front
side of the bike. Insert two bolts
(M8x20L) with lock washers (SW8)
and arc washers (M8x18x1.5T) into
the holes. Tighten with the 5mm 
L-shaped wrench.

• Slide the seat onto the seat post
stud. Tighten the 14mm nuts on the
bottom side of the seat to secure in
place. 

• Slide the seat post into the frame
seat post bracket.

• Insert the adjustment knob through
the seat post bracket and turn to tighten.

• Attach left and right pedal straps to
left and right pedals.

• Attach left and right pedals to left
and right crank arms. 

NOTE: both

pedals and crank arms should be
labeled left or right. Tighten with the
included pedal wrench.

• Plug in power supply to power
socket on the front side of the bike.

• Refer to Product Selection and
Model Configuration

decal on

console or follow these steps.

• Once the product is plugged in turn
on the console

• Select product (Bike (BK) or Elliptical
(EP)) using the resistance arrow keys.
Press ENTER to select.

• Select model number (Bike (1500,
2050, 2250, 3200) or Elliptical
(1500, 6000, 6200)) using the
RESISTANCE arrow keys. Press
ENTER to select. Console will reset to
start-up screen.

• The product selection and model
configuration is now complete.