Vision Fitness X70 ユーザーズマニュアル

ページ / 3
4
STEP
5
STEP
•  Remove  the  four  mounting  screws 
from the back of the console. Remove 
the  four  console  back  cover  screws.
Connect the wire harness and heart rate 
wires that come from the console mast 
into the plugs located in the back of the 
console. Attach the console to the mast 
with the four screws removed earlier.
• Plug in the 9-volt battery. Re-attach 
the console back cover with the four 
screws previously removed.
• Attach accessory tray to the console 
mast with the two included screws and 
screwdriver. Insert the water bottle.
CONSOLE
Link Arm 
Cover
Dual-Action 
End Cap
Dual-Action 
Arm
Rotation Housing
3
STEP
5
STEP
3
STEP
• Connect the right dual-action arm to 
the  right  console  mast  rotation  hous-
ing,  being  sure  to  line  up  the  holes. 
Secure  the  dual-action  arm  in  place 
with four screws (M8x20L) and tighten 
with  the  6mm  T-handled  wrench. 
Snap  the  dual-action  end  cap  into 
place.
• Make sure the spacers are inserted 
into the outside holes of the ball and 
socket  joint  of  the  lower  link  arm. 
Connect the right lower link arm to the 
right dual-action arm by lining up the 
holes on the end of  each arm. Slide 
the  screw  (M10x50L)  through  the 
hole. Place a nut (M10) on the screw 
and  tighten  using  the  17mm  socket 
wrench and 6mm T-handled wrench.
PINK BAG
Pedal Arm
Lower Link Arm
2
STEP
2
STEP
• Place a wavy washer (M20) on the 
axle  located  under  the  foot  plate  of 
the right lower link arm.
• Slide the axle of the lower link arm 
into the bracket located on the top of 
the right pedal arm. Secure the lower 
link arm to the pedal arm by attaching 
the pedal support bracket and screw 
(M8x20L)  to  the  end  of  the  axle. 
Secure the outside holes in the bracket 
to  the  footplate  with  two  sockethead 
capscrews (M8x10L). Tighten screws 
with the 5mm T-handled wrench.
•  Repeat  the  same  steps  on  the  left 
side
BLUE BAG
1
STEP
• Place the console mast boot on the 
end of the console mast.
•  Connect  the  wire  tie  that  exits  the 
bottom of the console mast to the wire 
harness  that  sits  in  the  bracket  at  the 
top of the frame. Pull the wire tie and 
wire  harness  up  through  the  console 
mast  while  at  the  same  time  insert-
ing  the  console  mast  into  the  frame 
bracket.
•  Secure  the  console  mast  to  the 
frame  with  two  capscrews  (M10  x 
70L).  Tighten  with  the  8mm  L-shaped 
wrench.
• Stabilize the console mast by insert-
ing the socket head screw (M8x80L) to 
the front of the bracket. Tighten with the 
8mm L-shaped wrench.
•  Slide  the  console  mast  boot  down 
the console mast and snap it in place 
so it integrates with the side covers.
ORANGE BAG
1
STEP
Bracket
Console Mast Boot 
Console Mast 
Accessory Tray
Console
Console Back Cover
• Position the link arm cover over the 
joint  of  the  lower  link  arm  and  dual-
action  arm.  With  a  screw  (M5x12L) 
and the screwdriver, connect the two 
halves  of  the  cover  through  the  hole 
located  in  the  front  of  the  cover. 
Attach  the  cover  to  each  side  of  the 
lower  link  arm  with  the  two  washers 
(M5) and two screws (M5x12L).
•  Repeat  these  same  steps  on  
the leftside.
BLACK BAG
4
STEP
X70_091111.indd   2
11/11/09   9:11 AM