Patton electronic SmartNode 4110 Series ユーザーズマニュアル
VoIP profile configuration task list
587
SmartWare Software Configuration Guide
47 • VoIP profile configuration
T.38 CED retransmission
Even if the user has configured redundant transmission for low-speed and high-speed packets the T.30 Indica-
tor messages are not included in this process. If the CED message gets lost, the remote device only receives the
CED Tone that is sent in-band. But the transmitted in-band tone may be short due to T.38 switchover or too
much distortion, such as by using a low bit-rate voice coder like G.723. In this case it is possible that the
remote device never starts the initial T.30 procedure, because it has never received the CED tone. For that rea-
son SmartWare sends the CED three times in an interval of 100ms with the same sequence number. With this
command, you can disable this feature or set the number of retransmissions to a user defined value.
tor messages are not included in this process. If the CED message gets lost, the remote device only receives the
CED Tone that is sent in-band. But the transmitted in-band tone may be short due to T.38 switchover or too
much distortion, such as by using a low bit-rate voice coder like G.723. In this case it is possible that the
remote device never starts the initial T.30 procedure, because it has never received the CED tone. For that rea-
son SmartWare sends the CED three times in an interval of 100ms with the same sequence number. With this
command, you can disable this feature or set the number of retransmissions to a user defined value.
Mode: profile voip profile-name
4
(optional)
node(pf-voip)[name]#fax volume
volume
volume
Adjusts the volume of the fax signals re-generated
on the receiver side. The volume is in dB, in the
range -18.5 ... -3.5 (Default: -9.5dB).
on the receiver side. The volume is in dB, in the
range -18.5 ... -3.5 (Default: -9.5dB).
5
(optional)
node(pf-voip)[name]# fax max-bit-
rate { 2400 | 4800 | 7200 | 9600 |
12000 | 14400 }
rate { 2400 | 4800 | 7200 | 9600 |
12000 | 14400 }
Sets maximum allowed bit-rate for fax relay
(Default 14400 Bit/sec).
(Default 14400 Bit/sec).
6
(optional)
node(pf-voip)[name]# fax detection
{ ced-tone | fax-frames }
{ ced-tone | fax-frames }
Selects the method when fax transmissions are
detected: By CED tone or by fax frames (Default:
ced-tone). It takes longer to detect Fax frames than
CED tones, but the risk of misdetection is mini-
mized.
detected: By CED tone or by fax frames (Default:
ced-tone). It takes longer to detect Fax frames than
CED tones, but the risk of misdetection is mini-
mized.
7
(optional)
node(pf-voip)[name]#no fax error-
correction
correction
Disables error correction mode (Default: enabled).
If the error correction mode is disabled, the con-
nected fax devices cannot negotiate error correc-
tion mode. Connections with error correction mode
enabled are more sensitive to packet loss. Disable
error correction mode when packet loss is more
than 2–3%.
If the error correction mode is disabled, the con-
nected fax devices cannot negotiate error correc-
tion mode. Connections with error correction mode
enabled are more sensitive to packet loss. Disable
error correction mode when packet loss is more
than 2–3%.
Note
Error correction mode does
not cancel IP packet loss.
not cancel IP packet loss.
8
(optional)
node(pf-voip)[name]#no fax hdlc
Disables HDLC image transfer (Default: enabled).
If HDLC mode is enabled, the SmartNode removes
bit-stuffing, checks CRCs of fax frames arriving
from the PSTN and regenerates the CRCs before
sending fax frames towards the PSTN. HDLC can
only be enabled together with error correction.
Disable HDLC when the fax peer does not support
this mode.
If HDLC mode is enabled, the SmartNode removes
bit-stuffing, checks CRCs of fax frames arriving
from the PSTN and regenerates the CRCs before
sending fax frames towards the PSTN. HDLC can
only be enabled together with error correction.
Disable HDLC when the fax peer does not support
this mode.
Step
Command
Purpose
1
[name] (pf-voip)[name]#[no] fax ced-
retransmission number
retransmission number
Specifies the number of CED retransmissions.
Default: 2
Default: 2
Step
Command
Purpose