Mitsubishi Electronics WS-65815 ユーザーズマニュアル
90
91
1.
The TV remote control does not work.
• Check that the batteries are installed correctly.
• Check that the select switch is set to “TV”.
• Be no further than 20 feet from the TV when using the remote control.
• Check that the select switch is set to “TV”.
• Be no further than 20 feet from the TV when using the remote control.
2.
The TV takes several seconds to respond.
• It is normal for digital channels to take longer to tune in.
• Press ENTER after a channel number to avoid delays.
• Press ENTER after a channel number to avoid delays.
• Use a 4 digit number for an over-the-air digital channel
• Use a 6 digit number for cable digital channels
• Use a 6 digit number for cable digital channels
3.
Cable provider needs information to start
CableCARD™ service.
CableCARD™ service.
• On the remote control, press TV MENU and then enter the numbers
999 to display the Host ID and CableCARD™ ID information.
999 to display the Host ID and CableCARD™ ID information.
4.
You cannot access a channel.
• Use number keys instead of CHANNEL up/down.
• Be sure the channel you want to view is in memory.
• Check that the TV is turned to the correct device or antenna for
that channel, by pressing the DEVICE button.
• Make sure the V-Chip lock is off.
• If tuned to Digital channels, have physical channel in memory.
• Be sure the channel you want to view is in memory.
• Check that the TV is turned to the correct device or antenna for
that channel, by pressing the DEVICE button.
• Make sure the V-Chip lock is off.
• If tuned to Digital channels, have physical channel in memory.
5.
On-screen displays appear each time you
change a function.
change a function.
• This is part of normal TV operation.
6.
You cannot program the TV to turn on
automatically (timer function)
automatically (timer function)
• The TV may be locked.
• The clock may not be set.
• The clock may not be set.
7.
There is no sound even when the volume is
turned up.
turned up.
• See if the MUTE button is on.
• The TV’s “Listen to:” setting may be set to SAP.
• Audio is set up through the NetCommand® menu. Use the Edit
NetCommand menu to review audio settings, including individual
device’s connection screens (ex: Connection for VCR). Checkmark
desired audio choices.
• If using the TV Speakers, make sure that TV Speakers setting is On in
the Audio/Video menu.
• The TV’s “Listen to:” setting may be set to SAP.
• Audio is set up through the NetCommand® menu. Use the Edit
NetCommand menu to review audio settings, including individual
device’s connection screens (ex: Connection for VCR). Checkmark
desired audio choices.
• If using the TV Speakers, make sure that TV Speakers setting is On in
the Audio/Video menu.
8.
The sound does not match the screen picture.
• NetCommand is setup incorrectly. Inputs must match actual
connections. Review through NetCommand menu.
• The TV’s “Listen to:” setting may be set to SAP.
• If using stereo or A/V receiver speakers, check their input selection.
• If using stereo or A/V receiver, check that AUDIO 2 of MONITOR
OUTPUT on TV’s back panel is connected to the A/V receiver.
connections. Review through NetCommand menu.
• The TV’s “Listen to:” setting may be set to SAP.
• If using stereo or A/V receiver speakers, check their input selection.
• If using stereo or A/V receiver, check that AUDIO 2 of MONITOR
OUTPUT on TV’s back panel is connected to the A/V receiver.
9.
NetCommand unable to learn specific device
keys.
keys.
• Device does not use IR format for remote control signal. ITT and
RF formats cannot be learned.
• Room lighting may affect the signal. Have the remotes very close
(6 inches or less) to the TV during Learning.
• If using a Mitsubishi remote control make sure slide switch is not
set to TV position.
• Not all device functions can be learned by NetCommand. For
example, POWER and PLAY are learned, but other functions are not.
• The signal from the remote control may not be strong enough. Insert
fresh batteries and try Learning again.
RF formats cannot be learned.
• Room lighting may affect the signal. Have the remotes very close
(6 inches or less) to the TV during Learning.
• If using a Mitsubishi remote control make sure slide switch is not
set to TV position.
• Not all device functions can be learned by NetCommand. For
example, POWER and PLAY are learned, but other functions are not.
• The signal from the remote control may not be strong enough. Insert
fresh batteries and try Learning again.
10.
You have forgotten your V-Chip passcode.
• See Appendix A, Bypassing the V-Chip Lock.
11.
PIP does not display a picture.
• Make sure the V-Chip lock is off.
• Not all inputs can be displayed as a PIP.
12.
Digital channels do not appear in PIP.
• Only analog channels are available for PIP’s.
13.
Not all channels appear in multiple PIP/POP.
• Digital channels do not display in PIP/POP.
14.
There is a large black or gray rectangle on the
screen.
screen.
• The TV’s analog closed captioning has been set to “text” mode in
the Captions menu. Turn off in Closed Caption menu because no
text information is being broadcast.
the Captions menu. Turn off in Closed Caption menu because no
text information is being broadcast.
15.
You cannot see a picture when playing a VHS
tape.
tape.
• Display the Device Selection menu and select the correct VCR.
• Check your VCRs owner’s guide for further trouble shooting.
• Check your VCRs owner’s guide for further trouble shooting.
16.
V-Chip is not working.
• Make sure that V-Chip is On.
• If V-Chip Hours are currently set to disable the V-Chip lock, the
V-Chip will not block programming.
• If V-Chip Hours are currently set to disable the V-Chip lock, the
V-Chip will not block programming.
Problem
Possible Solution
Troubleshooting