Toshiba 62HM116 ユーザーズマニュアル
30
HM116 (E/F) Web 213:276
Chapter 4: Setting up your TV
Setting the Quick Restart
™
feature
With the Quick Restart
™
feature set to On, the TV will stay in
Standby mode for several minutes after the TV is turned off
(see Note below).
If the TV is turned on from Standby mode, the full picture
appears immediately.
(see Note below).
If the TV is turned on from Standby mode, the full picture
appears immediately.
To set the Quick Restart
™
feature:
1
Press Y and open the Setup menu.
2
Highlight Quick Restart and press c.
3
Press b or B to select either On or Off and Press T.
Note: If Quick Restart is set to Off and you turn off the TV, it
can take several seconds for the picture to appear when you
turn on the TV again. See “Important Notice about Hot Lamp
Restart,” below.
can take several seconds for the picture to appear when you
turn on the TV again. See “Important Notice about Hot Lamp
Restart,” below.
If Quick Restart is set to On and you turn off the TV, the
following will occur for a few minutes:
following will occur for a few minutes:
• The screen (lamp) lights dimly; and
• The fans continue to run.
This is a function of the Quick Restart Shutdown mode and is
not a TV malfunction. If you do not prefer this, set the Quick
Restart feature to Off.
not a TV malfunction. If you do not prefer this, set the Quick
Restart feature to Off.
When the Quick Restart feature is set to Off, if you repeatedly
turn the TV on and off in a short period of time, the useful
service life of the lamp may be shorter than the average useful
service life (
turn the TV on and off in a short period of time, the useful
service life of the lamp may be shorter than the average useful
service life (
- page 81).
Viewing the digital signal meter
You can view the digital signal meter for the ANT 1 and
ANT 2 digital TV input sources only.
ANT 2 digital TV input sources only.
To view the digital signal meter:
1
Press Y and open the Setup menu.
2
Highlight Installation and press T.
3
A new set of Installation menu icons will appear, as shown
below.
Open the Terrestrial menu, highlight Signal Meter,
and press T.
below.
Open the Terrestrial menu, highlight Signal Meter,
and press T.
4
Press BbC c to select the antenna input and digital
channel whose signal you want to check.
channel whose signal you want to check.
Note: The physical digital channel number listed in the
Signal Meter screen may not correspond to a virtual TV
channel number. Contact your local broadcasters to
obtain the RF channel numbers for your local digital
stations.
Signal Meter screen may not correspond to a virtual TV
channel number. Contact your local broadcasters to
obtain the RF channel numbers for your local digital
stations.
To close the screen and return to the Terrestrial
menu:
menu:
Highlight Done and press T.
To return to normal viewing:
Press O.
IMPORTANT NOTICE ABOUT HOT LAMP RESTART
When the TV has been powered on long enough for the
lamp unit to get hot, it may take several minutes for the
picture to appear in the following situations:
lamp unit to get hot, it may take several minutes for the
picture to appear in the following situations:
•
When the Quick Restart
™
feature is set to Off and you
turn the TV off and then on again within a few minutes;
or
or
•
If the TV is on when a short-term power failure, power
surge, or other similar power failure occurs, such that
the TV loses and regains power within a few minutes.
surge, or other similar power failure occurs, such that
the TV loses and regains power within a few minutes.
This is a property of DLP
™
technology and is NOT a
sign of malfunction.
If this occurs, the yellow LED on the TV front panel will
blink (and the blue LED will be lit solid) until the TV is
finished restarting the lamp and the normal picture
appears. If both LEDs are blinking, you will need to turn
the TV off and then on again to restart the lamp.
If this occurs, the yellow LED on the TV front panel will
blink (and the blue LED will be lit solid) until the TV is
finished restarting the lamp and the normal picture
appears. If both LEDs are blinking, you will need to turn
the TV off and then on again to restart the lamp.
CH RTN
ENTER
EXIT
Navigate
Select
Back
Exit
On
Off
On
Auto
Auto
2 Sec
No
No
Quick Restart
ColorStream HD1 Audio
HDMI 1 Audio
ColorStream HD2 Audio
HDMI 2 Audio
Slide Show Interval
Setup
CH RTN
ENTER
EXIT
Navigate
Select
Back
Exit
Terrestrial
Input Configuration
Channel Program
Channel Add/Delete
Signal Meter
Signal Meter
Antenna
1
Physical Digital Channel
4
Virtual Digital Channel
Done
4-1
Signal Locked
0
0
Peak
HM116_EN.book Page 30 Monday, June 19, 2006 7:30 PM