Alpine IDA-X300 ユーザーズマニュアル
9
-EN
iDA-X200
iDA-X300
This unit cannot receive HD Radio signals (digital terrestrial radio). In
order to activate the digital radio functions described below, an optional
HD Radio Tuner module must be connected through the Ai-NET bus.
order to activate the digital radio functions described below, an optional
HD Radio Tuner module must be connected through the Ai-NET bus.
Listening to Radio
HD Radio can be received if the HD Radio TUNER MODULE
(TUA-T500HD) is connected. While receiving HD Radio, the unit can
automatically switch between the analog and digital signal.
automatically switch between the analog and digital signal.
1
Press
SOURCE to select TUNER mode.
2
Press BAND repeatedly until the desired radio band
is displayed.
is displayed.
FM1
FM2
AM
FM1
3
Press TUNE/A.ME to select the tuning mode.
DX SEEK (Distance mode)
SEEK (Local mode)
(Blank) (Manual mode)
DX SEEK (Distance mode)
• The initial mode is Distance mode.
Distance mode:
Both strong and weak stations will be automatically tuned in
(Automatic Seek Tuning).
(Automatic Seek Tuning).
Local mode:
Only strong stations will be automatically tuned in (Automatic
Seek Tuning).
Seek Tuning).
Manual mode:
The frequency is manually tuned in steps (Manual tuning).
4
Press
or
to tune in the desired station.
Holding down
or
will change the frequency
continuously.
• If DIGITAL SEEK is set to ON, the SEEK UP/DOWN functions only
stop on digital station frequencies while receiving HD radio. Refer to
“Digital Seek On/Off Setting” (page 25).
“Digital Seek On/Off Setting” (page 25).
Presetting Stations Manually
1
Select the radio band and tune in a desired radio
station you wish to store in the preset memory.
station you wish to store in the preset memory.
2
Press PRESET.
The Preset screen is displayed.
3
Turn the Double Action encoder (iDA-X200 only)
or Rotary encoder (iDA-X300 only) to select the
preset number.
or Rotary encoder (iDA-X300 only) to select the
preset number.
4
Press and hold
/ENTER for at least 2 seconds.
The selected station is stored.
The display shows the band, preset number and station
frequency memorized.
The display shows the band, preset number and station
frequency memorized.
• A total of 18 stations can be stored in the preset memory (6 stations
for each band; FM1, FM2 and AM).
• If you store a station in a preset memory which already has a station,
the current station will be cleared and replaced with the new station.
Presetting Stations Automatically
1
Press BAND repeatedly until the desired radio band
is displayed.
is displayed.
2
Press and hold TUNE/A.ME for at least 2 seconds.
The tuner will automatically seek and store 6 strong stations
in the selected band. They will be stored 1 to 6 in order of
signal strength.
When the automatic memory has been completed, the tuner
goes to the station stored in preset location No.1.
in the selected band. They will be stored 1 to 6 in order of
signal strength.
When the automatic memory has been completed, the tuner
goes to the station stored in preset location No.1.
• If no stations are stored, the tuner will return to the original station
you were listening to before the auto memory procedure began.
Tuning to Preset Stations
1
Press BAND repeatedly until the desired band is
displayed.
displayed.
2
Press PRESET.
The Preset screen is displayed.
3
Turn the Double Action encoder (iDA-X200 only)
or Rotary encoder (iDA-X300 only) to select a
radio station.
or Rotary encoder (iDA-X300 only) to select a
radio station.
4
Press
/ENTER.
The display shows the band, preset number and frequency
of the station selected.
of the station selected.
Radio
TUNE/A.ME
/ENTER
PRESET
Double Action
encoder
encoder
VIEW
SOURCE
FUNC./SETUP
BAND
TUNE/A.ME
/ENTER
PRESET
Rotary encoder
VIEW
SOURCE
FUNC./SETUP
BAND