Cobra Electronics PR 945 ユーザーズマニュアル
A D V
A N C E D O P E R AT I O N
A D VA N C E D O P E R AT I O N
ENGLISH
8
Using the MODE Button
The MODE button allows you to use and program the
various functions of your microTALK
®
radio. If you press and
hold the MODE button, the LCD will cycle through the
different functions.
different functions.
Programming Memor
y Locations
Y
our microTALK
®
radio has ten (10) memory locations
(0-9) for storing your most frequently used channels and
privacy codes.
privacy codes.
T
o program locations:
1.
Push the MODE button until the Memor
y icon and the
memory location flashes.
2.
Press the CHANNEL SELECT button up or down to select
the memory location you wish to change.
3.
Press and release the MODE button again. The Memor
y
icon and the main channel number will flash.
4.
Press the CHANNEL SECTECT button to select the main
channel you wish to store.
5.
Press the MODE button again to store the main channel
in memory and move to privacy code selection. The
privacy code number begins flashing and the Memory
icon continues to flash.
privacy code number begins flashing and the Memory
icon continues to flash.
6.
Press the CHANNEL SELECT button to select the privacy
code (00-38) you wish to store.
7.
Press the LOCK button to program your selection.
You may also press the TALK button to transmit your
selected channel and privacy code, which will be stored
into the memory location you are using.
selected channel and privacy code, which will be stored
into the memory location you are using.
8.
a)
Press and release the LOCK button to return to
Standby mode at your new memory location.
Standby mode at your new memory location.
b) Press and release the MODE button to save the
memory location and proceed to other functions.
(
NOTE:
T
o “unprogram” a memory location you
programmed previously, select 00 for both the main
channel and privacy code in steps 4 through 6.)
channel and privacy code in steps 4 through 6.)
ENGLISH
7
Recalling Memory Locations
To recall a channel you have stored in a
memory location:
memory location:
1.
Press the MODE button until the Memor
y icon and a
memory location flashes.
2.
Select your desired memor
y location by pushing the
CHANNEL SELECT button up or down.
Your radio will stay at this memory location until you exit
Memory Function mode by pressing the LOCK button.
Repeat steps 1 and 2 to recall other memory locations.
Memory Function mode by pressing the LOCK button.
Repeat steps 1 and 2 to recall other memory locations.
Using the Scan Function
Y
our microTALK
®
radio can automatically scan main
channels (1-22), the privacy codes (00-38) within one
main channel, or memory locations.
main channel, or memory locations.
T
o scan main channels:
1.
Press the MODE button until the Scan icon and main
channel number flashes.
2.
Push the CHANNEL SELECT button up or down and the
radio will begin scanning the main channels.
(
NOTE:
The radio “ignores” privacy codes while scanning
main channels.)
3.
The radio will continue to scan all main channels and
stop if an incoming transmission is detected. The radio
will remain on that channel for ten (10) seconds.
During that time you can:
will remain on that channel for ten (10) seconds.
During that time you can:
a) Press and hold the TALK button and talk. The radio will
remain on that channel and return to Standby mode.
b) Push the CHANNEL SELECT button up or down to
resume scanning main channels.
c) Press the MODE button to proceed to privacy code
scanning (see following page).
If you do not press any button within ten (10) seconds,
the radio will automatically resume scanning main
channels.
the radio will automatically resume scanning main
channels.
MODE
Button
MODE
Button
MODE
Button
TALK
Button
MODE
Button
LOCK
Button
CHANNEL
SELECT
Button
CHANNEL
SELECT
Button
MODE
Button
CHANNEL
SELECT
Button