Philips 42PFL7486H ユーザーズマニュアル
EN 39
En
gl
is
h
Update channel list
When the TV was switched on for the first
time, a full installation of channels was
performed.
You can automatically add or remove digital
channels or manually update channels.
Note: If you are prompted to enter a code,
enter '8888'.
Automatic update
To automatically add or remove digital
channels, leave the TV in standby mode. The
TV updates channels and stores new
channels everyday. Empty channels are
removed from the channel list.
If a channel update is performed, a message
appears at startup.
time, a full installation of channels was
performed.
You can automatically add or remove digital
channels or manually update channels.
Note: If you are prompted to enter a code,
enter '8888'.
Automatic update
To automatically add or remove digital
channels, leave the TV in standby mode. The
TV updates channels and stores new
channels everyday. Empty channels are
removed from the channel list.
If a channel update is performed, a message
appears at startup.
If you do not want this message to appear
1. Press .
1. Press .
2. Select [Setup] > [Channel settings] or
[Satellite settings].
3. Select [Channel installation] > [Channel
update message].
4. Select [Off], then press OK.
To disable automatic updates
In the [Channel installation] menu, select
[Automatic channel update] > [Off].
[Satellite settings].
3. Select [Channel installation] > [Channel
update message].
4. Select [Off], then press OK.
To disable automatic updates
In the [Channel installation] menu, select
[Automatic channel update] > [Off].
Automatic install
When the TV was switched on for the first
time, a full installation of channels was
performed. You can run this full installation
again to set your language, country and install
all available TV channels.
Note:
[Search for satellite] is only available if the
TV supports DVB-S.
1. Press .
time, a full installation of channels was
performed. You can run this full installation
again to set your language, country and install
all available TV channels.
Note:
[Search for satellite] is only available if the
TV supports DVB-S.
1. Press .
2. Select [Setup] > [Search for channels] or
[Search for satellite], then press OK.
3. Follow the onscreen instructions to
complete the channel installation.
[Search for satellite], then press OK.
3. Follow the onscreen instructions to
complete the channel installation.
4. Once complete, select [Finish], then press
OK.
Tip: Press FIND to see the channel list.
OK.
Tip: Press FIND to see the channel list.
Notes:
During installation, leave settings
unchanged unless your digital provider
gives you the specific values to enter.
unchanged unless your digital provider
gives you the specific values to enter.
When digital TV channels are found,
the list of installed channels may display
empty channel numbers. You can
rename, reorder or uninstall these
channels.
the list of installed channels may display
empty channel numbers. You can
rename, reorder or uninstall these
channels.
Access DVB-C or DVB-T channels
If you have installed both DVB-C and DVB-T
channels, you have to switch to the
respective network to watch channels on
that network.
1. While you watch TV, press .
If you have installed both DVB-C and DVB-T
channels, you have to switch to the
respective network to watch channels on
that network.
1. While you watch TV, press .
2. Select [Setup] > [Channel settings].
3. Select [Channel installation] > [Antenna
or Cable DVB].
4. Select one of the following settings:
3. Select [Channel installation] > [Antenna
or Cable DVB].
4. Select one of the following settings:
[Antenna (DVB-T)]: Access free-to-air
antenna or digital DVB-T channels.
antenna or digital DVB-T channels.
[Cable]: Access cable or digital DVB-C
channels.
channels.
5. Press OK to confirm.
6. Press to exit.
The TV switches to the selected channel list.
Access DVB-S channels (for certain models
only)
If your satellite is connected to the SAT
connector, you can receive satellite channels.
Press > [Watch satellite] to watch
satellite channels.
6. Press to exit.
The TV switches to the selected channel list.
Access DVB-S channels (for certain models
only)
If your satellite is connected to the SAT
connector, you can receive satellite channels.
Press > [Watch satellite] to watch
satellite channels.
Install analogue channels
You can search and store analogue TV
channels manually.
Step 1: Select your system
Note: Skip this step if your system settings
are correct.
1. While you watch TV, press .
channels manually.
Step 1: Select your system
Note: Skip this step if your system settings
are correct.
1. While you watch TV, press .
2. Select [Setup] > [Channel settings] >
[Channel installation].
3. Select [Analogue: Manual installation] >
[System], then press OK.
4. Select the system for your country or
[Channel installation].
3. Select [Analogue: Manual installation] >
[System], then press OK.
4. Select the system for your country or
region, then press OK.