ICOM IC-F3022T ユーザーズマニュアル

 

When adjusting IC-F3020 series, CS-F3020 

CLONING SOFTWARE,

 CS-F3020 ADJ 

ADJUSTMENT SOFTWARE

 (Rev. 1.0 or later), 

OPC-478/U 

JIG CABLE

 (modifi ed OPC-478/U 

CLONING CABLE

; see the page 6-2) and the following test equipments are required.

DC power supply

Output voltage         
Current capacity      

: 7.2 V DC
: More than 1.5 A

External speaker

Input impedance 
Capacity 

: 8 

Ω

: 1 W or more

FM deviation meter

Frequency range 
Measuring range 

: DC–300 MHz
: 0 to 

±10 kHz    

Attenuator

Power attenuation 
Capacity 

: 20 or 30 dB
: 7.5 W

Frequency counter

Frequency range
Frequency accuracy 
Sensitivity 

: 0.1–300 MHz
: ±1 ppm or better 
: 100 mV or better

Standard signal 
generator (SSG)

Frequency range 
Output level   

: 0.1–300 MHz
:  0.1 µV to 32 mV

(–127 to –17 dBm) 

RF power meter

Measuring range   
Frequency range  
Impedance     
SWR 

: 0.1–7.5 W
: 100–300 MHz
: 50 

Ω

: Better than 1.2 : 1

Oscilloscope

Frequency rang  
Measuring range 

: DC–20 MHz
: 0.01–20 V 

6 - 1

▄ SYSTEM REQUIREMENTS 

(for the ADJUSTMENT SOFTWARE)

• Microsoft

®

 Windows

®

 98/98SE/Me/2000/XP        • RS-232C serial port (D-sub 9 pin) or USB port 

▄  STARTING SOFTWARE ADJUSTMENT

q  Connect the transceiver and PC with OPC-478/U 

JIG 

CABLE

.

w Turn the transceiver power ON.
e  Boot up Windows, and click the program group ‘CS-F3020 

ADJ’ in the ‘Programs’ folder of the [Start] menu, then 
CS-F3020 ADJ’s window appears.

r  Click ‘Connect’ on the CS-F3020 ADJ’s window, then the 

window shows transceiver’s condition and adjustment 
items as below.

t  Set or modify adjustment data as specifi ed.

Clone the adjustment frequencies and settings into the 
transceiver, and set the confi guration using the CS-F3020 

CLONING SOFTWARE

 before starting the software adjustment. 

Otherwise, the software adjustment can not be started.

CAUTION!:  BACK UP the originally programmed memory 

data in the transceiver before programming the 
adjustment frequencies. When program the ad-
justment frequencies into the transceiver, the 
transceiver’s memory data will be overwritten 
and lose original memory data at the same time.

Microsoft and Windows are registered trademarks of Micro-
soft Corporation in the U.S.A. and other countries.

q Quit all applications when Windows is running.
w

 Insert the CD into the appropriate CD drive.

e

  Double-click the “Setup.exe” contained in the ‘CS-F3020 

ADJ’ folder in the CD drive.

r

  The “Welcome to the InstallShield Wizard for CS-F3020 

ADJ” will appear. Click [Next>].

t

  The “Choose Destination Location” will appear. Then click 

[Next>] to install the software to the destination folder. (e.g. 
C:\Program Files\Icom\CS-F3020 ADJ)

y

 

 

After the installation is completed, the “InstallShield Wiz-
ard Complete” will appear. Then click [Finish].

u

 Eject the CD.

i

  Program group ‘CS-F3020 ADJ’ appears in the ‘Programs’ 

folder of the start menu, and ‘CS-F3020 ADJ’ icon ap-
pears on the desk top screen.

1

174.000 MHz

TX power
Mode

: Low1
: Narrow

2

136.000 MHz

TX power
Mode

: Low1
: Wide

3

155.000 MHz

TX power
Mode

: High
: Wide

4

155.000 MHz

TX power
Mode

: Low2
: Wide

5

155.000 MHz

TX power
Mode

: Low1
: Narrow

6

155.000 MHz

TX power
Mode
DTCS

: Low1
: Narrow
: 007

7*

155.000 MHz

TX power
Mode

: Low1
: Middle

8

155.000 MHz

TX power
Mode
CTCSS

: Low1
: Wide
: 151.4 Hz

9

155.000 MHz

TX power
Mode

: Low1
: Wide

*; [EUR] only