Bosch FPA-1200-MPC-C ユーザーズマニュアル
MPC-xxxx-C / FPA-1200-MPC-C
en
17
Bosch Sicherheitssyteme GmbH
F.01U.258.925 | 2.0 | 2012.04
Functional Description
The Panel Controller controls every component connected to the panel and features the
following functional elements (see Figure 1, Page 4):
following functional elements (see Figure 1, Page 4):
Installation
The FPA-1200-MPC-C Panel Controller is only used with the FPA-1200 Fire Panel.
The MPC-XXXX-C Panel Controller may be mounted into the following FPA-5000 housings:
CPH 0006 A, MPH 0010 A, HCP 0006 A and HBC 0010 A.
For the installation, follow the instructions given in Figure 2 to Figure 4 (Page 5 to Page 7):
1.
The MPC-XXXX-C Panel Controller may be mounted into the following FPA-5000 housings:
CPH 0006 A, MPH 0010 A, HCP 0006 A and HBC 0010 A.
For the installation, follow the instructions given in Figure 2 to Figure 4 (Page 5 to Page 7):
1.
Make sure that the PRS 0002 A Panel Rail Short is mounted before you start installing the
Panel Controller.
Panel Controller.
2.
Connect the ground wire to the screw on the housing (Step 4, Figure 3, Page 6).
3.
Plug the cable into the slot labeled "IN" of the PRS 0002 A Panel Rail Short (Step 6,
Figure 3, Page 6).
Note: Do not plug the cable into the slot labeled "OUT" nor into the slots of the
PRD 0004 A Panel Rail Long.
Figure 3, Page 6).
Note: Do not plug the cable into the slot labeled "OUT" nor into the slots of the
PRD 0004 A Panel Rail Long.
4.
Plug the EOL resistor for the databus into the slot labeled "OUT" of the last panel rail
PRS/PRD in use (Step 8, Figure 4, Page 7).
PRS/PRD in use (Step 8, Figure 4, Page 7).
Wiring
The Panel Controller features
-
-
2 CAN interfaces (CAN1/CAN2) for networking
-
2 Ethernet interfaces (ETH1/ETH2) for networking
-
2 signal inputs (IN1/IN2)
-
1 USB and 1 RS232 interface
Consider the maximum cable length of 2 m when using the USB and RS232 interfaces (see
Figure 5, Page 8).
Figure 5, Page 8).
WARNING!
Live components and stripped cable! Risk of injury from electric shock. The system must be
current-free during connection work.
current-free during connection work.
NOTICE!
Installation must only be performed by authorized and specialized personnel!
NOTICE!
The CD includes the FSP-5000-RPS Programming Software and the required product
documentation of the panel.
documentation of the panel.
Pos. Designation
Function
A
Touch screen
Operating the panel through virtual buttons and variable display windows
B
22 fixed buttons
Standard entries
C
11 LEDs
Indicating the operating status
D
Key switch
2 switch settings, freely programmable, e.g. for switching between day/
night mode, or connection/disconnection to and from the local alarm
signaling
night mode, or connection/disconnection to and from the local alarm
signaling
E
3 rotary switches
Address setting
F
Reboot button
Panel HW reset
G
6-pin DIP switch
Configuration
H
Ground wire
Grounding the panel
NOTICE!
You will find detailed information about the CAN and Ethernet networking of the panels in the
Networking Guide available for download at www.boschsecurity.com.
Networking Guide available for download at www.boschsecurity.com.