ユーザーズマニュアル目次Notices3FCC notice3Class A equipment3Shielded cables3Peripheral devices4Use conditions4Canadian users4Laser compliance statement4Important safety instructions51 System information13Product briefing15Processor15Memory subsystem15Storage16Graphics interface16Networking16I/O ports16Caring features17Product specification summary182 System tour19System board21Connector and Header Locations21Configuration Jumpers23Serial Port Configuration Jumper24BIOS Select Jumper25Back Panel Connectors26External and internal structure28Front panel29Rear view32Optional Peripherals33Internal components343 Getting Started35Setting up the system37Preinstallation requirements37System startup38Turning on the system38Turning off the system38Power-on problems394 Configuring the system41Upgrading the system43Installation precautions43Opening the server45Before opening the server45Removing the Chassis Cover45Installing the Chassis Cover47Removing and Installing the Front Bezel48Removing the Front Bezel48Installing the Front Bezel48Removing and Installing the Processor Air Duct49Removing the Processor Air Duct49Installing the Processor Air Duct49Removing and Installing the Air Baffle50Removing the Air Baffle50Installing the Air Baffle52Installing and Removing a Hard Disk Drive53Installing a Fixed SATA Hard Disk Drive53Removing a Fixed SATA Hard Disk Drive58Installing a SATA or SCSI Hot-swap Hard Disk Drive60Removing a SATA or SCSI Hot-swap Hard Disk Drive62Installing or Removing a Floppy Drive64Installing a Floppy Drive into Slimline Bay (Backplane Installed)64Removing a Floppy Drive from the Slimline Bay (Backplane Installed)67Installing a Floppy Drive into Slimline Bay (No Backplane Installed)67Removing a Floppy Drive from the Slimline Bay (No Backplane Installed)72Installing a Floppy Drive into the Converted Hard Drive Bay (Backplane Installed)73Removing a Floppy Drive from the Converted Hard Drive Bay76Installing or Removing a DVD/CD-RW or CD-ROM Drive78Installing a DVD/CD-RW or CD-ROM Drive into Slimline Bay (Backplane Installed)78Removing a DVD/CD-RW or CD-ROM Drive from the Slimline Bay (Backplane Installed)80Installing DVD/CD-RW or CD-ROM Drive into Slimline Bay (No Backplane Installed)81Installing and Removing a PCI Riser Connector84Installing a PCI Riser Connector84Removing a PCI Riser Connector86Installing and Removing a PCI Add-in Card88Installing a PCI Add-in Card88Removing a PCI Add-in Card89Installing and Removing the SATA or SCSI Backplane (Optional)91Removing the SATA or SCSI Backplane91Installing the SCSI or SATA Backplane92Processor Installation and Upgrade95Installing or Replacing the Processor95Installing the Processor95Installing the Heat Sink(s)97Removing a Processor98Memory Installations and Upgrade99Upgrading the system memory99Memory Sparing101Installing and Removing Memory102Installing DIMMs102Removing DIMMs1035 BIOS setup105Using the BIOS Setup Utility107Entering BIOS107If You Cannot Access Setup107Setup Menus107BIOS Setup Utility108BIOS Setup Keyboard Command Bar Options109Main111Advanced113Upgrading the BIOS150Clearing the Password151Clearing the CMOS1526 Troubleshooting155Hardware Diagnostic Testing158Specific Problems and Corrective Actions159Appendix A: Management software installation169Installing ASM171System requirements171System setup171Tool-less rail kit installation177Setting the Multi-Pin Adapters for Rack Type177Installing the Slide Rails into the Rack178Installing the Component into the Slide Rails180Required Installation Position of the CMA182General Safety Information185Appendix B: Tool-less rail kit installation175Appendix C: Sensor Table187Sensor Table189Appendix D: SATA RAID Configuration191Configuring the onboard SATA RAID193How to enable the onboard SATA RAID function193How to create RAID 1 volume193Loading onboard SATA RAID default setting193Index197サイズ： 7.54MBページ数： 198Language: Englishマニュアルを開く
