ユーザーガイド目次1.0 ATTO FibreBridge provides storage options6ATTO FibreBridge 2370E features, benefits6ATTO FibreBridge 2390C/R/D features, benefits7ATTO FibreBridge 2400C/R/D features, benefits71.1 ATTO FibreBridge 2370E8Board dimensions8Cooling and airflow8Power8Fibre Channel port8SCSI ports8Management access8LED indicators8Exhibit 1.1-1 FibreBridge 2370E board layout91.2 ATTO FibreBridge 2390R/D10Dimensions10Cooling and airflow10Power10Fibre Channel interface10SCSI ports10Management ports10Manual reset switch11LED indicators11Exhibit 1.2-1 Fibre Bridge 2390R/D dimensions with front panel LEDs and connector side details111.3 ATTO FibreBridge 2390C12Board dimensions12Cooling and airflow12Power12Fibre Channel port12SCSI ports12Management access12Manual reset switch12LED indicators12Exhibit 1.3-1 The FibreBridge 2390C connectors and LEDS.13Exhibit 1.3-2 The FibreBridge 2390C board layout.131.4 ATTO FibreBridge 2400R/D14Dimensions14Cooling and airflow14Power14Fibre Channel port14SCSI ports14Management ports14Manual reset switch15LED indicators15Exhibit 1.4-1 Connectors, LEDs and power receptacle on the connector side and LEDs on the faceplate151.5 ATTO FibreBridge 2400C16Board dimensions16Cooling and airflow16Power16Fibre Channel port16SCSI ports16Management access16LED indicators16Exhibit 1.5-1 FibreBridge 2400C bracket detail and board layout172.0 Install the FibreBridge18Unpack the packing box; verify contents18Install the FibreBridge18Discover the IP address18Internet Explorer setup19Begin initial configuration19Exhibit 2.0-1 Brackets to install the FibreBridge 2390R/D or 2400R/D into a rack.19Exhibit 2.0-2 Typical FibreBridge connectors, LEDs and power receptacle193.0 Configure the FibreBridge20Preliminary steps20Port configurations20Modify passwords20Enhance performance213.1 Map devices22FibreBridge mapping22SCSI device mapping22Mapping devices automatically23Mapping devices manually.23Multiple Node addressing (FB2400 only)233.2 Remote monitoring, management24Exhibit 3.0-3 The Remote Management page in the ExpressNAV interface24SNMP-based monitoring25Exhibit 3.0-4 Events triggering SNMP notification for extended or standard trap generation, severity level and explanation25Email messages provide error notification26Exhibit 3.0-5 The Email messages sent by the FibreBridge follow this format.27Exhibit 3.0-6 Events triggering an Email message, severity level and explanation274.0 Update firmware28Preliminary step28Using ExpressNAV28Using FTP28Using the zModem command285.0 Interface options30Using ExpressNAV30Opening an ExpressNAV session30Optimizing ExpressNAV in Internet Explorer30Using the serial port30Using Telnet31Appendix A Cabling32SCSI port connections32Fibre Channel connections32Serial port connections32Ethernet connections32Appendix B CLI provides ASCII-based interface33Exhibit 0.0-1 Symbols, typefaces and abbreviations used to indicate functions and elements of the command line interface used in this manual.33CLI error messages34CLI summary reference34Command explanations37Appendix C Standards and compliances48FCC Standards: Radio and Television Interference48Canadian Standards48European Standards48Declaration of Conformity48Certification for the FibreBridge 2400 only49Appendix D Warranty information50Manufacturer limited warranty50サイズ： 1.6MBページ数： 51Language: Englishマニュアルを開く
