Furuno 711c マニュアル

目次

• IMPORTANT NOTICES

  3
• SAFETY INSTRUCTIONS

  4
• TABLE OF CONTENTS

  6
• FOREWORD

  9
• SYSTEM CONFIGURATION

  10
• EQUIPMENT LISTS

  11
• 1. OPERATIONAL OVERVIEW

  13
  • 1.1 Controls

    13
  • 1.2 How to Turn the Power On/Off

    14
    • 1.2.1 How to power the system

      14
    • 1.2.2 How to power off the system

      14
  • 1.3 How to Adjust the Brilliance

    15
  • 1.4 How to Set the Display Color

    15
  • 1.5 How to Select a Display

    16
    • 1.5.1 Graphic displays

      16
    • 1.5.2 Numerical Display

      19
    • 1.5.3 How to select the display data

      20
    • 1.5.4 How to select the display data with the key operation(STBY mode only)

      22
• 2. STEERING MODES

  23
  • 2.1 STBY Mode

    23
  • 2.2 AUTO Mode

    23
    • 2.2.1 How to get the AUTO mode

      24
    • 2.2.2 Advanced AUTO mode

      25
  • 2.3 NAV Mode

    26
    • 2.3.1 How to get the NAV mode

      27
    • 2.3.2 Sailing method for the NAV mode

      28
    • 2.3.3 Waypoint switching method

      29
    • 2.3.4 How to set the steering behavior of your boat after you arrive to a waypoint

      30
  • 2.4 Response Feature

    31
    • 2.4.1 How to activate the auto response feature

      31
    • 2.4.2 How to activate the manual response feature

      31
  • 2.5 TURN Mode

    32
    • 2.5.1 How to select a normal turn and start the turn

      32
    • 2.5.2 Types of normal turns

      33
  • 2.6 FishHunterTM Mode

    35
    • 2.6.1 How to select a FishHunterTM turn and start the turn

      35
    • 2.6.2 Types of the FishHunterTM turn

      38
    • 2.6.3 How to set FishHunterTM turn parameters

      42
  • 2.7 How to Navigate to a TLL Position

    43
  • 2.8 DODGE Mode

    44
    • 2.8.1 How to dodge in the AUTO and NAV modes

      44
    • 2.8.2 How to FU dodge in the STBY mode

      44
    • 2.8.3 How to NFU dodge in the STBY mode

      44
  • 2.9 REMOTE Mode

    45
    • 2.9.1 Dial-type remote controller (FAP-5551, FAP-5552)

      45
    • 2.9.2 Button-type remote controller (FAP-6211, FAP-6212), Lever-type remote controller (FAP-6221, FAP-6222)

      46
    • 2.9.3 Dodge-type remote controller (FAP-6231, FAP-6232)

      47
  • 2.10 WIND Mode (for sailboats)

    48
    • 2.10.1 How to get the WIND mode

      48
    • 2.10.2 Wind angle mode

      49
    • 2.10.3 TACK mode

      50
    • 2.10.4 Tacking in WIND mode (WIND TACK)

      52
  • 2.11 OVRD mode (for IPS drive)

    56
  • 2.12 Safe Helm Mode

    57
  • 2.13 Power Assist Mode

    59
• 3. ALARMS

  61
  • 3.1 Alarm Menu

    61
  • 3.2 Alarm Buzzer

    62
  • 3.3 Buzzer Interval

    62
  • 3.4 Watch Alarm

    63
  • 3.5 Deviation Alarm

    63
  • 3.6 XTE Alarm

    64
  • 3.7 Arrival Alarm

    64
  • 3.8 Speed Alarm

    65
  • 3.9 Depth Alarm

    65
  • 3.10 Water Temperature Alarm

    66
  • 3.11 Trip Distance Alarm, Trip Distance Reset

    67
    • 3.11.1 How to set the trip log alarm

      67
    • 3.11.2 How to reset the trip distance

      67
  • 3.12 Wind Alarms (for sailboats)

    68
    • 3.12.1 Heading change alarm

      68
    • 3.12.2 Wind deviation alarm

      69
    • 3.12.3 True and apparent wind speed alarm

      69
  • 3.13 Alarm Log

    70
• 4. USER MENU

  71
  • 4.1 Parameter Setup

    71
    • 4.1.1 Sea state

      71
    • 4.1.2 Trim gain

      74
    • 4.1.3 Speed calculation

      75
  • 4.2 Rudder Drive Level (For Fantum FeedbackTM)

    75
  • 4.3 Net Towing

    76
  • 4.4 Course After Operation of a Remote Controller

    77
  • 4.5 Nav Data Source

    78
  • 4.6 NavNet vx2 Synchronization

    79
  • 4.7 System Setup Menu

    79
  • 4.8 Menu Shortcuts

    81
    • 4.8.1 How to create a menu shortcut

      81
    • 4.8.2 How to delete a menu shortcut

      81
• 5. MAINTENANCE, TROUBLESHOOTING

  83
  • 5.1 Preventive Maintenance

    83
  • 5.2 Replacement of Fuse

    84
  • 5.3 Diagnostics

    84
    • 5.3.1 Diagnostic menu

      84
    • 5.3.2 Processor unit test

      85
    • 5.3.3 Control unit test

      86
    • 5.3.4 EVC interface test

      86
    • 5.3.5 NMEA0183 test

      87
    • 5.3.6 CAN bus test

      87
    • 5.3.7 Key test

      88
    • 5.3.8 Screen test

      88
    • 5.3.9 Rudder test

      89
    • 5.3.10 Helm sensor test

      93
  • 5.4 System Data

    94
  • 5.5 Messages

    94
    • 5.5.1 Message pop-up display

      94
    • 5.5.2 Message board

      95
    • 5.5.3 Message description

      95
  • 5.6 Sensor in Use Display

    98
• 6. INSTALLATION AND WIRING

  99
  • 6.1 Installation

    99
    • 6.1.1 Installation location

      99
    • 6.1.2 When FAP-7011 is replaced with FAP-7011C

      100
    • 6.1.3 How to install the control unit

      101
  • 6.2 Wiring

    103
    • 6.2.1 Wiring notices

      104
    • 6.2.2 Connection with the processor unit

      105
• 7. INITIAL SETTINGS

  107
  • 7.1 How to Select Language and Units, Open the Installation Menu Window

    107
  • 7.2 Display Setup

    109
  • 7.3 Ship’s Characteristics Menu

    110
  • 7.4 Dockside Setup Menu

    111
    • 7.4.1 Dockside setup for the rudder reference unit

      111
    • 7.4.2 Dockside setup for Fantum FeedbackTM

      117
    • 7.4.3 How to set the safe helm mode and power assist mode

      121
    • 7.4.4 Confirmation of the dockside setup

      125
  • 7.5 CAN bus Port Setup

    129
  • 7.6 NMEA0183 Port Setup

    131
  • 7.7 Sensor Setup

    133
  • 7.8 Universal Port Setup

    134
    • 7.8.1 GENERAL IN port setup

      134
    • 7.8.2 GENERAL OUT port setup

      135
  • 7.9 Sea Trial

    136
    • 7.9.1 How to calibrate the compass (PG-500/PG-700)

      137
    • 7.9.2 How to set the rudder deadband

      139
  • 7.10 Data Calibration

    140
  • 7.11 Parameter Setup Menu

    141
    • 7.11.1 Sea state

      141
    • 7.11.2 Trim gain

      144
    • 7.11.3 Speed calculation

      145
  • 7.12 AUTO Option Menu

    145
  • 7.13 NAV Option Menu

    146
    • 7.13.1 How to select the source for nav data

      147
  • 7.14 Fish Hunter Option Menu

    148
  • 7.15 Wind Option Menu

    149
  • 7.16 System Setup Menu

    150
  • 7.17 RC (Remote Controller) Setup Menu

    151
  • 7.18 All Clear (Default Setting)

    151
• APPENDIX 1 MENU TREE

  153
• APPENDIX 2 JIS CABLE GUIDE

  158
• SPECIFICATIONS

  159
• PACKING LIST

  161
• OUTLINE DRAWING

  162
• INTERCONNECTION DIAGRAM

  163
• INDEX

  164
• FURUNO Worldwide Warranty for Pleasure Boats

  166
• FURUNO Warranty for North America

  167
• MOUNTING TEMPLATE

  168