Honeywell ISM BAND XYR 5000 LINE マニュアル

目次

• INTRODUCTION

  1
• USING THIS MANUAL

  1
• ABOUT THE DEVICE

  1
• UNPACKING

  2
• SOFTWARE COMPATIBILITY

  2
• QUICK START

  3
• Figure 2-1 Overall Wiring Schematic

  3
• INSTALLATION

  5
• MECHANICAL INSTALLATION

  5
• 3.1.1 Base Radio Positioning

  5
• Figure 3-1 General Layout

  6
• ELECTRICAL INSTALLATION

  7
• 3.2.1 Electrical Specifications

  7
• Figure 3-2 Overall Wiring Schematic

  8
• Figure 3-3 Terminal Block Labels

  8
• 3.2.2 Wiring Power to the Base Radio

  9
• 3.2.3 Wiring RS-485 to the Base Radio

  9
• Figure 3-4 Wiring Power to the Base Radio

  9
• 3.2.4 Wiring the RS-485/232 Converter to the Base Radio

  10
• Figure 3-5 Wiring RS-485 to the Base Radio

  10
• Figure 3-6 Base Radio to RS-232 Converter Wiring Diagram

  10
• Radio

  11
• 485/Power

  12
• Figure 3-7 Daisy-Chaining Power to Multiple Base Radios

  13
• Radio

  14
• Figure 3-8 Daisy-Chaining RS-485 to Multiple Base Radios

  14
• Figure 3-9 Example of End Unit in Daisy-Chain Configuration

  14
• 3.2.8 Grounding the Base Radio

  15
• 3.2.9 High Gain Antenna

  15
• Figure 3-10 Example of Correct Termination Resistor Setup

  15
• GENERAL CONFIGURATION

  16
• BASE RADIO DISPLAYED MESSAGES

  16
• 4.1.1 The Read Only Sequence

  16
• Figure 4-1 Base Radio Power-Up and Operations LCD Sequences

  16
• OVERALL CONFIGURATION MENU MAP

  17
• Figure 4-2 The Read Only Sequence

  17
• Figure 4-3 Overall Configuration Menu Map

  17
• SETTING THE USER PASSWORD

  18
• CONFIGURING THE RF COMMUNICATIONS

  19
• RF CHANNEL SELECTION

  19
• Figure 5-1 Menu Map to RF Channel Setting

  19
• RF BAUD RATE SELECTION

  20
• Figure 5-2 Menu Map to RF Baud Rate Setting

  20
• HIGH RF ID SETTING

  21
• CONFIGURING THE MODBUS COMMUNICATIONS

  22
• BASE RADIO SETUP

  22
• 6.1.1 Modbus Baud Rate Setting

  22
• 6.1.2 Modbus Device ID Setting

  23
• Figure 6-1 Menu Map to Modbus Baud Rate Setting

  23
• Figure 6-2 Menu Map to Modbus Device ID Setting

  24
• 6.1.3 Modbus Parity Setting

  25
• 6.1.4 Modbus Mapping Mode Setting

  25
• Figure 6-3 Menu Map to Modbus Parity Setting

  25
• MODBUS COMMUNICATION PROTOCOL

  26
• Figure 6-4 Menu Map to Modbus Mapping Mode Setting

  26
• MODBUS COMMANDS

  27
• 6.3.1 Command 03-Read Holding Registers

  27
• 6.3.2 Command 08- Diagnostic

  27
• 6.3.3 Command 11- Get Com Event Counter

  28
• 6.3.4 Command 12- Get Com Event Log

  28
• 6.3.5 Command 17- Report Slave ID

  28
• 6.3.6 Command 43- Read Device ID

  29
• BASE RADIO HOLDING REGISTERS

  29
• 6.4.1 Base Radio Device Type Registers

  30
• 6.4.2 Base Radio Device Status Registers

  30
• 6.4.3 Base Radio On/Offline Transmitter Registers

  30
• TRANSMITTER HOLDING REGISTERS

  31
• 6.5.1 Device ID Mapping Mode

  31
• 6.5.2 Register Mapping Mode

  31
• 6.5.3 Transmitter Device Type Holding Registers

  32
• 6.5.4 Transmitter Device Status Registers

  33
• SQUARE ROOT FUNCTION

  33
• TECHNICAL SPECIFICATIONS

  34
• Figure 7-1 Overall Base Radio Dimensions

  35
• NAVIGATING THE MENUS

  36
• BASE RADIO MENU MAP

  37
• MODBUS REGISTER DEFINITIONS

  38