ユーザーズマニュアル目次VIS elements2Back shot VIS installation.3Typical Over Lane Site Layout5Typical Over Lane Site Layout Plan.6VIS 300 U.S. Camera options chart.8VIS 300 European Camera options chart.11Typical side of road installation.14Typical side of road installation plan view with no canopy/overhead structue.14Flash and camera distances.15Install the traffic light sensor.17TLS-300 signal and power cable.18Installing the TLS-300 through the mounting pipe and flange.18Pipe clamps should be about 6-inches apart on a vertical surface.19Camera Installation19Camera mount template.20Camera cabling as it appears before electrical installation.20Cable final wiring.21Properly wired X-4 connector.22Back of the video camera.22VIS CAM connections24TLS 300 to J-Panel wiring.25X-6 Power input connection.26Wiring for the X8 to converter connector.27Test trigger28Two lane controller29TNF-31 flash unit29S3 switch setting30Connecting an AC flash.30Connection for LVD to VIS CAM 400.31Example of a network connection using a local switch.35Initial Camera Alignment Display example.37Roll Bar Display example.38Readjustment of camera tilt and zoom display.39Focus Bar marker display.40Focus Bar Waveform display.41Focus Bar Waveform Display with waveform cursors42Connection requirements.45Component layout of the EN board.46Board connections47Interface drawing.48Electrical interface48Physical interface table49Category 5 or 6 wiring diagram.50Flash connections.50I/O board electrical interface. Test51Switch location.51Connecting DC Flash to a board powered from the Flash power supply.52Connection DC Flash to an internally powered board.52AC flash unit connection.53Second flash connection.53IO board electrical interface.54Wiring a second DC flash from the flash power supply.55Connecting the second AC flash.56Connecting to the night light (TNC 100)57Detection board57LVD Trigger Input58Electrical interface on the I/O board:58Ethernet test connectors.59EN network test configuration setup.60Test setup 2.61Auxiliary power connector62EN-CAM component layout.65Connecting from J-Panel to camera zero.65J-Panel electrical interface66Ethernet wiring diagram.68Board and camera J-panel connection to camera 1.69J-panel electrical interface70Category 5 or 6 ethernet wiring diagram.71Light sensor indicator on the board72Light sensor connector72Signal to J-panel #273Signal from J-panel #174Signal from J-panel #175Principle in the power distribution.76RS485 to Ethernet76Interface from Camera 077Interface from Camera 178External Trigger connection.79Trigger polarity80Trigger 080Trigger 180Lane controller setup diagram81Lane controller setup.82Two camera, one flash, configuration.83Terminal block85Standard configuration of Basic Settings:87Standard configuration of Network Settings:88Standard configuration of Serial settings for port 1:89Standard configuration of Serial settings for port 2:90Configuration overview of serial port 1 and 2.90Operation configuration of Serial port 1:91Operation configuration of Serial port 2:92Configuration overview of operating settings for serial port 1 and 2.92Moxa configuration example.93Network cabling example:95Light Sensor Cables18Electrical wiring for the VIS CAM installation.21VIS CAM connections to the J-Panel.23TLS 300 to J-Panel connections24Power input to the J-Panel25X8 to converter connector26Trigger input connector27X15 Lane Controller28Flash unit connection in VIS CAM 400.29Optimal Illumination Distance Between Camera and TNF30Wiring for LVD to VIS CAM 400.31Typical minimum plate heights and nominal plate heights:34Optimal Illumination Distance Between Camera and TNF43Wiring diagram.51Physical interface pinouts.55Connector table59Signal parameters and conditions.66Physical interface table67LED indicators68Switch labels68Signal table70Ethernet physical connections71LED indicators72Connector switches72Physical interface connections73LED physical indicators73Physical connector table for J-panel 2.74Physical pin connections J-panel #1.75Physical connection for pins.76RS485 physical connections77Physical connector description78Pin connections for Ethernet from Camera 179Connector table81WAGO physical interface82Master to slave connections.84Essential specifications for the pluggable terminal block.85Troubleshooting table.97サイズ: 4.79MBページ数: 112Language: Englishマニュアルを開く