Netgear WN203 - ProSAFE® WIRELESS-N SINGLE BAND ACCESS POINT マニュアル

目次

• ProSAFE Single Band 802.11n Wireless Access Point WN203

  1
• Contents

  3
• 1. Introduction

  6
  • About the ProSAFE Single Band 802.11n Wireless Access Point WN203

    7
  • What Is in the Box?

    7
  • System Requirements

    8
  • Key Features and Standards

    8
    • Supported Standards and Conventions

      8
    • Key Features

      9
    • 802.11b/g/n Standards–Based Wireless Networking

      10
    • Autosensing Ethernet Connections with Auto Uplink

      11
  • Hardware Description

    11
    • Front Panel

      11
    • Back Panel

      12
    • Bottom Panel with Product Label and Reset to Factory Defaults Button

      13
• 2. Installation and Basic Configuration

  14
  • What You Need Before You Begin

    15
    • Wireless Equipment Placement and Range Guidelines

      15
    • Ethernet Cabling Requirements

      16
    • LAN Configuration Requirements

      16
    • Hardware Requirements for Computers on Your LAN

      16
    • Requirements for Entering IP Addresses

      16
  • Install and Configure the Wireless Access Point

    16
    • Connect the Wireless Access Point to a Computer

      17
    • Log In to the Wireless Access Point

      18
    • Configure Basic General System Settings and Time Settings

      20
    • Configure the IP Settings

      22
    • Configure the Optional DHCP Server

      23
    • Configure the Basic Wireless Settings

      25
  • Test Basic Wireless Connectivity

    28
• 3. Wireless Configuration and Security

  30
  • Before You Configure Wireless Security

    31
  • Wireless Data Security Options

    31
  • Security Profiles

    33
    • Security Profile Concepts

      34
    • Write Down Your Wireless Network Settings

      35
    • Configure and Enable Security Profiles

      36
  • Configure RADIUS Server Settings

    45
  • Restrict Wireless Access by MAC Address

    46
  • Schedule the Wireless Radios to Be Turned Off

    49
  • Configure Basic Wireless Quality of Service

    49
• 4. Management

  51
  • Enable Remote Management

    52
    • SNMP Management

      52
    • Secure Shell and Telnet Management

      53
  • Upgrade the Wireless Access Point Software

    54
    • Web Browser Upgrade Procedure

      55
    • TFTP Server Upgrade Procedure

      56
  • Manage the Configuration File or Reset to Factory Default

    57
    • Save the Configuration

      57
    • Restore the Configuration

      58
    • Restore the Wireless Access Point to the Factory Default Settings

      58
    • Reboot the Wireless Access Point without Restoring the Default Configuration

      60
  • Change the Administrator Password

    61
  • Enable the Syslog Option

    62
  • Enable Rogue AP Detection and Monitor Access Points

    62
    • Enable and Configure Rogue AP Detection

      63
    • View and Save Access Point Lists

      64
• 5. Advanced Configuration

  67
  • Configure Spanning Tree Protocol and 802.1Q VLANs

    68
  • Configure Hotspot Settings

    69
  • Configure Advanced Wireless Settings

    70
  • Configure Advanced Quality of Service Settings

    73
  • Configure Wireless Bridging

    75
    • Configure a Point-to-Point Wireless Network

      76
    • Configure a Point-to-Multipoint Wireless Network

      81
    • Configure the Wireless Access Point to Repeat the Wireless Signal Using Point-to-Multipoint Bridge Mode

      85
• 6. Monitoring

  91
  • View System Information

    92
  • Monitor Wireless Clients

    94
  • View the Activity Log

    96
  • Traffic Statistics

    97
• 7. Troubleshooting

  99
  • Basic Functioning

    100
    • Verify the Correct Sequence of Events at Startup

      100
    • No LEDs Are Lit on the Wireless Access Point

      100
    • LAN LED Is Not Lit

      101
    • WLAN LED Is Not Lit

      101
  • You Cannot Access the Internet or the LAN from a Wireless-Capable Computer

    101
  • You Cannot Configure the Wireless Access Point from a Browser

    102
  • When You Enter a URL or IP Address a Time-Out Error Occurs

    103
  • Troubleshoot a TCP/IP Network Using the Ping Utility

    103
    • Test the LAN Path to Your Wireless Access Point

      103
    • Test the Path from Your Computer to a Remote Device

      104
  • Problems with Date and Time

    105
• A. Supplemental Information

  106
  • Technical Specifications

    107
  • Factory Default Settings

    108
• B. Command-Line Reference

  112
• Index

  124