TANDBERG codian isdn gateway isdn gw 3201 マニュアル

目次

• Table of contents

  4
• General information

  5
  • About the ISDN gateway

    5
  • Package contents

    5
  • Port and LED location

    5
    • Figure 1: ISDN gateway front panel

      5
  • LED behavior

    6
    • Table 1: ISDN gateway LED behavior

      6
• Connecting the ISDN gateway

  8
  • Before you start

    8
  • Your ISDN connection

    8
    • Outside North America

      8
    • Within North America

      8
  • Step one: Connect power

    9
  • Step two: Connect to Ethernet Port A

    9
  • Step three: Connect to the ISDN ports

    9
• Initial configuration

  10
  • Step one: Connect to the console port

    10
    • 1 Ensure power is connected to the ISDN gateway and the Status LED is green.

      10
      • 2 Connect the console port of the ISDN gateway to the serial port of your PC using the blue RJ45 to DB9 console cable supplied.

        10
      • 3 Use a serial terminal program, such as Secure CRT or HyperTerminal, to connect to the ISDN gateway. Set your terminal software to the following settings:

        10
      • 4 Press Enter and the following command prompt appears on the terminal:

        10
  • Step two: Configure Ethernet Port A settings

    10
    • 1 To configure Ethernet Port A, enter the following for auto-sensing mode:

      11
      • 2 To display the current configuration and status of the Ethernet ports, enter: status

        11
  • Step three: Assign an IP address to the ISDN gateway (optional)

    11
  • Step four: Discover the IP address of the ISDN gateway

    11
    • 1 To display the current status of the IP address, enter: status

      11
      • 2 Make a note of the IP address. You will use this to access the web interface of the unit.

        11
• Configuring the ISDN gateway

  12
  • Step one: Log in to the ISDN gateway

    12
    • 1 Use your browser to navigate to the IP address of the ISDN gateway (to discover the IP address, refer to the previous section).

      12
      • 2 Click Change log in and enter the user name admin with no password.

        12
  • Step two: Set up the ISDN interfaces

    12
    • 1 In the web interface, go to Settings > ISDN.

      12
      • 2 Select the ISDN interface type to match that of your installation; E1 is typically used in the UK and mainland Europe, T1 (USA and Canada) in North America, and T1(Japan) in Japan.

        12
      • 3 Complete the other settings as required by your network, referring to the online help for further information.

        12
      • 4 Click Apply changes to save any changes you have made to the configuration.

        12
      • 5 Restart the ISDN gateway (this is only necessary if you changed the ISDN configuration). To do this:

        12
      • 6 When the ISDN gateway has restarted, log in to the web interface again, and go to Settings > ISDN ports.

        12
      • 7 Complete the settings for ISDN Port 1 as required by your network, referring to the online help for further information. Note that all ISDN ports on the ISDN gateway are enabled by default.

        12
      • 8 Click Apply changes to save your configuration changes to the ISDN port.

        12
      • 9 If required, configure another ISDN port by selecting the port number from the numbered links at the top right of the ISDN port configuration page.

        12
  • Step three: Configure an H.323 gatekeeper

    13
  • Step four: Configure the dial plan

    13
    • IP to ISDN dial plan setup

      13
    • 1 In the web interface, go to Dial plan > IP to ISDN and click Add rule.

      13
      • 2 For Condition, select Called number matches and enter the correct match for example 9(D*).

        13
      • 3 For Action, select Call this number and enter $1.

        13
      • 4 For Call type, select Telephone.

        13
      • 5 Leave the other values unchanged. Click Add rule to add the rule to the dial plan.

        13
      • 6 Repeat steps 1 to 5 to create a second dial plan to accept and forward the video calls with the correct format in Called number matches, for example 8(D*) and for Call type, select Video.

        13
      • ISDN to IP dial plan setup

        14
    • 1 Go to Dial plan > ISDN to IP, and click Add rule.

      14
      • 2 For Condition, select Called number matches and enter the correct match for example D*(DD), which will match the last 2 digits of the dialed number. To match the last 3 digits, use D*(DDD).

        14
      • 3 For Action, select Call this number and enter 59$1.

        14
      • 4 For Call type, select Video.

        14
      • 5 Leave the other values unchanged. Click Add rule to add the rule to the dial plan.

        14
    • 1 Go to Dial plan > ISDN to IP, and click Add rule.

      14
      • 2 For Condition, select Match any called number.

        14
      • 3 For Action, select Enter the auto attendant + TCS-4.

        14
      • 4 For Call type, select Video.

        14
      • 5 Leave the other values unchanged. Click Add rule to add the rule to the dial plan.

        14
• Troubleshooting and technical support information

  15
  • Calls fail to complete

    15
  • Using the event log to help solve a problem

    15
  • Getting more help

    16
    • 1 Refer to the Technical FAQ and Troubleshooter sections of the web site. We keep both sections up to date with the latest information from our technical support team regarding the resolution of customer issues.

      16
      • 2 Contact your reseller. Our resellers have a wealth of experience with our products and this is sometimes a quick way of solving a problem.

        16
      • 3 If your query remains unsolved, there is a web form in the Support area of the web site that you can complete. Ensure that you provide all the details requested by the form to assist the technical support team in resolving your problem:

        16
• Pin outs

  17
  • Table 2: Pin assignments for PRI ports

    17
  • Figure 2: Pin numbering for PRI ports

    17