Viewsonic PJD6240 マニュアル

目次

• Introduction

  8
  • Projector Features

    8
  • Package Contents

    9
• Projector with Lens Cap

  9
• AC Power Cord

  9
• VGA Cable (D-SUB to D-SUB)

  9
• Quick Start Guide

  9
• VGA - Component Adapter

  9
  • Projector Overview

    10
• Using the Product

  12
  • Control Panel

    12
  • Connection Ports

    13
  • Remote Control

    14
• Installing the Batteries

  15
  • 1. Open the battery cover in the direction shown.

    15
  • 2. Install batteries as indicated by the diagram Inside the compartment.

    15
  • 3. Close the battery cover into position.

    15
  • Remote Control Operation

    16
  • Installation

    17
    • Connecting the Projector

      17
    • Powering On/Off the Projector

      18
• Powering On the Projector:

  18
  • 1. Remove the projector lens cap.

    18
  • 2. Complete the AC power cord and peripheral signal cable(s) connections.

    18
  • 3. Press button to turn on the projector. The projector takes a minute or so to warm up.

    18
  • 4. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects your source.

    18
• Powering Off the Projector:

  18
  • 1. Press button to turn off the projector lamp. You will see a message "Power off? Press Power again" appear on the screen.

    18
  • 2. Press button again to confirm.

    18
  • 3. Disconnect the AC power cord from the electrical outlet and the projector.

    18
  • 4. Do not turn on the projector immediately following a power off procedure.

    18
  • Adjusting the Projector

    19
• Adjusting the Projector Height

  19
  • 1. To raise or lower the image, press the elevator button and raise or lower the front of the projector. Release the button to lock the adjustment.

    19
  • 2. To level the image on the screen, turn the tilt-adjustment foot to fine-tune the height.

    19
• Adjusting the Projector Zoom and Focus

  19
  • 1. Focus the image by rotating the focus ring. A still image is recommended for focusing.

    19
  • 2. Adjust the image by sliding the zoom ring.

    19
• Adjusting Projection Image Size

  20
  • Menu Operation

    21
    • 1. Press the Menu button on the control panel or the MENU button on the remote control to open the OSD menu.

      23
    • 2. When OSD is displayed, use p / q to select any feature in the main menu.

      23
    • 3. After selecting the desired main menu feature, press u to enter sub-menu for feature setting.

      23
    • 4. Adjust the settings with t / u.

      23
    • 5. Press the Menu buttonon the control panel or the MENU button on the remote control, the screen will return to the main menu.

      23
    • 6. To exit OSD, press the Menu button on the control panel or the MENU button on the remote control again. The OSD menu will close and the projector will automatically save the new settings.

      23
  • Maintenance

    38
    • Cleaning the Lens

      38
    • Cleaning the Projector Housing

      38
    • Replacing the Lamp

      39
      • 1. Turn off the projector.

        40
      • 2. If the projector is installed in a ceiling mount, remove it from the mount.

        40
      • 3. Unplug the power cord.

        40
      • 4. Loosen the screw in the side of the lamp cover and remove the cover.

        40
      • 5. Remove the screws from the lamp module, raise the handle, and lift out the module.

        40
      • 6. Insert the new lamp module into the projector and tighten the screws.

        40
      • 7. Replace the lamp cover and tighten the screw.

        40
      • 8. Turn on the projector. If the lamp does not turn on after the warm-up period, try reinstalling the lamp.

        40
      • 9. Reset the lamp hour. Refer to the “Setting” menu.

        40
  • Specifications

    41
  • Appendix

    42
    • LED Indicator Messages

      42
    • Compatibility Modes

      48
• Computer:

  48
• Video:

  48
  • Troubleshooting

    49
• Start-up problems

  49
• Image problems

  49