Accusplit AL1590M12 전단

Maximize the accuracy of your distance measurement by: 

•  Walking a measured 0.5 or 1.0 mile/km. (We recommend  

  that you use a 

1

⁄

4

-mile/400 meter track like those found at  

  a high school). 

•  Compare the DISTANCE recorded to the measured  

  distance. If the pedometer shows you walked LESS than  

  you actually did, reset your STEP LENGTH to a longer  

  setting. If the pedometer shows you walked MORE than  

  you actually did, reset the STEP LENGTH to a shorter  

  setting. 

To view the current week total data, press the gray WK-DAY 

button from any display mode. The total count so far for the 

current week is displayed. The word “WEEK” will appear in the 

upper right band corner of the display. Press the gray WK-DAY 

button again to return to today’s data. Or, press the black MODE 

button to cycle through the current week’s results.

1. To filter out random movements, the unit remains in standby  

  mode until 5 continuous steps are registered. Only then are  

  the 5 steps calculated in, and an Active indicator “▲” appears  

  on the upper left of display.
2. When regular walk/run movement stops, after 2 seconds the  

  timer pauses and the unit switches to standby status (Active  

  indicator “▲” disappears). 

RESETTING YOUR PEDOMETER 
Auto Zero Reset:

 The daily count of steps, distance, calories, 

and activity time resets each night automatically at 2:00 AM. 

However, the records will remain on the display until you have 

taken your first five steps (so that you can manually record them 

if desired). At 2:00 AM on Sunday, the previous week’s records 

will also be reset to zero, but they remain on the display until 

you’ve taken your first five steps of the week. At this point, the 

current week’s memories will be transferred to the previous 

week’s memories.
Manual Zero Reset:

 You can also manually reset your pedometer 

at any time. To reset today’s memories, first press the gray WK-

DAY button until the unit is in DAY mode. In DAY mode, you will 

see only one day of the week at the top of the display. Next, 

press and hold the yellow RESET button for at least 2 seconds. 

To reset the current week’s memories, first press the gray WK-

DAY button until the word “WEEK” appears in the upper right 

hand corner of the display. Next, press and hold the yellow 

RESET button for at least 2 seconds.

When the display starts to dim or goes blank, it is time to replace 

the battery. Your pedometer uses one Type LR44 1.5 volt alkaline 

battery. To replace:
1. Insert a coin into the slot on the bottom of the case, and twist  

  counterclockwise to loosen the case front. Lift case front away.
2. Using a pen or other thin object, push battery sideways out of  

  its holder. Replace it with a new battery. The battery’s positive  

  (+) terminal should be FACE UP while you put it into the  

  pedometer.
3. Align case front over the pedometer and press gently to snap  

  cover back into place, starting with top.

•  RESET display to zero.

•  Walk the track again to test the adjustment, and re-adjust  

  accordingly. 

•  Once adjusted DO NOT ALLOW ANYONE ELSE TO CHANGE  

  THE SETTING because the Activity Pedometer is now set for  

  your style. 

•  You are now ready to walk any route, change that route freely  

  and still get an accurate measurement of distance for your  

  fitness or recreation program.   

 

(Badge holder  

not included)

Attach the pedometer to the leash by 

looping the leash around the pedometer belt clip. Next, clasp 

the waistband of your clothing with the attached clip. You can 

also use a safety pin to fasten the leash to your clothing, or 

loop the leash through your belt or belt loop. 

Once you put on your pedometer with the cover closed, it will 

automatically begin to record your steps, distance, calories 

burned, and activity time. Repeatedly press the black MODE 

button to cycle through the pedometer modes: 

STEPS → DISTANCE → CALORIES → ACTIVITY TIMER → 

TIME OF DAY → STEPS

This pedometer has memories to keep track of today’s, this 

week’s, and last week’s step activity, distance, calories, and 

activity time. 
To view the previous week’s total data, press the gray PREV 

WK button from any display mode. The previous week’s total 

for that mode is displayed. Press the black MODE button 

to cycle through the display modes. All seven day of week 

indicator bars (at top of display) are visible when viewing 

PREVIOUS WEEK data. Press the gray PREV WK button to 

return to today’s data.