JL Audio SB-F-FCSZX/10W3v3 사용자 설명서
Specifications:
Enclosure Type: Acoustic Suspension (Sealed)
Driver Type: One JL AUDIO 10W3-D2 Subwoofer
Nominal Impedance: 4
Enclosure Type: Acoustic Suspension (Sealed)
Driver Type: One JL AUDIO 10W3-D2 Subwoofer
Nominal Impedance: 4
Ω
Cont. Power Handling: 250 Watts
JL Audio recommends using a high quality amplifier such as the JL Audio 250/1. The diagram below shows the recommended
crossover, infrasonic filter and equalizer settings for the 250/1 when being used to power your Stealthbox
®
.
Included Hardware:
(1) 3/8” Washer
(1) 3/8” Lock Washer
(1) 3/8” Hex nut
(1) 3/8” x 2 1/4” Socket Cup Set Screw
(1) 3/8” Washer
(1) 3/8” Lock Washer
(1) 3/8” Hex nut
(1) 3/8” x 2 1/4” Socket Cup Set Screw
10369 N. Commerce Pkwy, Miramar, Florida 33025 Phone: 954.443.1100 Fax: 954.443.1111
JL AUDIO 250/1
monoblock subwoofer amplifier
Amplifier Input Section
Input Sens.
Input Voltage
Low/High
Left Ch.
Right Ch.
Signal Sensing
Off/On
Output Mode
Full-Range/Low-Pass/High-Pass
Left Ch.
Right Ch.
Amp LP Filter
Mode/Slope
Off/12dB/24dB
Filter Freq. (Hz)
Bass Control
LF Boost (dB)
Off/30Hz
Infrasonic Filter
+1
+13
+3
+7
+10
Preamp Output Section
+12VDC
Ground
Remote
The JL Audio 250/1 is a very versatile audio component. Please consult the owner’s manual for detailed information
about installing and tuning this amplifier.
about installing and tuning this amplifier.
➔
➔
➔
Cont.
From
Page 3
➔
S B - F - Z X 3 / 1 0 W 3 , J L AU D I O, I n c 2 0 0 2
S h e e t S K U # 0 1 1 1 5 7 R ev i s i o n 0 6 / 1 8 / 0 2
Pa g e 3
w w w . j l a u d i o . c o m
Mid/High Frequency Driver Information:
CONGRATULATIONS!
INSTALL COMPLETE.
TR570-CXi
Front Location Driver Size:
5"x7”
5"x7”
Applicable JL Audio Products:
TR570-CXi,
XR570-CXi or CSi
TR570-CXi,
XR570-CXi or CSi
Rear Location Driver Size:
5"x7”
5"x7”
Applicable JL Audio Products:
TR570-CXi,
XR570-CXi or CSi
TR570-CXi,
XR570-CXi or CSi
STEP 11: Reinstall the plastic side panel and
the 4 Phillips head screws, the safety belt
retractor cover and cargo light removed in
Steps 1 & 2. Place cut carpet side panel back
into car.
the 4 Phillips head screws, the safety belt
retractor cover and cargo light removed in
Steps 1 & 2. Place cut carpet side panel back
into car.
STEP 12: Run speaker wire to the location of
the Stealthbox enclosure. At this time please
check for proper operation of woofer.
the Stealthbox enclosure. At this time please
check for proper operation of woofer.
STEP 13: Slide Stealthbox enclosure into the
corner of cargo area. Insert the 3/8 in.
threaded mounting stud into the enclosure
and line it up with the 1/2 in. (12.7 mm) hole.
Slide through to outside of car. Make sure
relocated MOLEX
corner of cargo area. Insert the 3/8 in.
threaded mounting stud into the enclosure
and line it up with the 1/2 in. (12.7 mm) hole.
Slide through to outside of car. Make sure
relocated MOLEX
®
plug and wiring is not
going to be pinched by enclosure or side
panels.
panels.
STEP 14: From outside of the car, slide hand
between the pulled fabric wheel well (Step
6) and the car’s body. Feel for the threaded
mounting stud.
between the pulled fabric wheel well (Step
6) and the car’s body. Feel for the threaded
mounting stud.
STEP 15: Place fender washer, lock washer
and 3/8 in. nut onto threaded mounting stud.
Tighten firmly using a 9/16 in. deep socket.
and 3/8 in. nut onto threaded mounting stud.
Tighten firmly using a 9/16 in. deep socket.
STEP 16: After securely mounting the
Stealthbox, push fabric wheel well back into
place. Reinstall TORX head bolt and Phillips
head screw that was removed in Step 5.
Stealthbox, push fabric wheel well back into
place. Reinstall TORX head bolt and Phillips
head screw that was removed in Step 5.
STEP 17: Replace hatch carpet back into car.You
will need to tuck the carpet under the Stealthbox.
will need to tuck the carpet under the Stealthbox.
XR570-CXi