Peerless Industries SWS320/BK 사용자 설명서
9 of 38
ISSUED: 11-21-07 SHEET #: 202-9255-5 05-12-10
© 2009, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.
Peerless Industries, Inc.
3215 W. North Ave.
Melrose Park, IL 60160
www.peerlessmounts.com
DETAIL 2
fi g 4.1
IncreLok™
TILT
LOCKING
SCREW
LOCATOR
HOLE
RATCHET
HANDLE
TILT
POSITION
HOLES
fi g 3.2
SAFETY/
SECURITY
SCREW
CROSS SECTION
DETAIL 1
AA
BB
&
CC
BB
&
CC
AA
fi g 3.1
RATCHET
HANDLE
Tension Adjustment of Ratchet Handle:
Adjust
tension in tilt brackets (BB & CC) by rotating
ratchet handle. NOTE: If obstruction prevents
ratchet handle from rotating, pull handle out while
turning will allow handle to reposition without
tightening. Release and turn handle to tighten or
loosen.
ratchet handle. NOTE: If obstruction prevents
ratchet handle from rotating, pull handle out while
turning will allow handle to reposition without
tightening. Release and turn handle to tighten or
loosen.
Mounting Screen: Ratchet handle must be in the
up or down position or interference will occur while
hooking tilt brackets to wall plate (AA). Slowly hook
tilt brackets (BB & CC) onto wall plate (AA) and
swing screen down as shown in fi g. 3.1. Tilt bracket
hooks must fully engage wall plate as shown in
detail 1. Using phillips screw driver or security allen
wrench (FF), turn safety/security screws on tilt
brackets (BB & CC) clockwise till screw tip securely
contacts wall plate as shown in cross section.
up or down position or interference will occur while
hooking tilt brackets to wall plate (AA). Slowly hook
tilt brackets (BB & CC) onto wall plate (AA) and
swing screen down as shown in fi g. 3.1. Tilt bracket
hooks must fully engage wall plate as shown in
detail 1. Using phillips screw driver or security allen
wrench (FF), turn safety/security screws on tilt
brackets (BB & CC) clockwise till screw tip securely
contacts wall plate as shown in cross section.
Screen Adjustment: Screen can be adjusted
horizontally by loosening safety/security screws
on tilt brackets (BB & CC) three full turns. Adjust
screen as shown in fi gure 3.2. Tighten safety/
security screws on tilt brackets till screw tip
securely contacts wall plate as shown in cross
section.
horizontally by loosening safety/security screws
on tilt brackets (BB & CC) three full turns. Adjust
screen as shown in fi gure 3.2. Tighten safety/
security screws on tilt brackets till screw tip
securely contacts wall plate as shown in cross
section.
Removing Screen: To remove screen from mount,
loosen safety screws, swing screen away from
mount, and lift screen off of mount.
loosen safety screws, swing screen away from
mount, and lift screen off of mount.
3
For preset tilt angles use Increlok
™ and for
custom tilt angle use ratchet handle.
INCRELOK
™
: The screen can be locked into a
pre-set tilt position of -5
°
, 0
°
, 5
°
, 10
°
or 15
°
. Use
locator hole to fi nd tilt position hole and tilt screen
to align holes. Tighten IncreLok™ tilt locking
screws on both tilt brackets to lock tilt as shown in
detail 2.
to align holes. Tighten IncreLok™ tilt locking
screws on both tilt brackets to lock tilt as shown in
detail 2.
Ratchet Handle:
Loosen ratchet handle (refer
to step 3 for tension adjustment of handle).
Push
or pull from top or bottom of screen to adjust tilt
as shown in fi g. 4.1. The tilt can be adjusted to a
maximum of 15° forward or 5° backward.
as shown in fi g. 4.1. The tilt can be adjusted to a
maximum of 15° forward or 5° backward.
Mounting and Removing Flat Panel Screen
Adjusting the Tilt Angle of the Flat Panel
Screen
Screen
• Always use an assistant or mechanical lifting equipment
to safely lift and position the fl at panel screen.
• Do not tighten screws with excessive force.
Overtightening can cause damage to mount. Tighten
screws to 40 in. • lb (4.5 N.M.) maximum torque.
screws to 40 in. • lb (4.5 N.M.) maximum torque.
• Be careful not to pinch fi ngers when pushing screen from
the bottom.
WARNING
4