Sony HVR-M25AU 사용자 설명서

60

Chapter 4

Dubbing to Other Equipment Using the i.LINK Jack, Duplication, Audio Dubbing, and Connecting a Computer

Cha

p

te

r 4

D

u

b

bi

ng
 to
 O

th

e

r E

q

u

ip

m

en
t Us

in

g t
he i

.L

IN

K J

a

c

k

, Du

pl

icat
io

n

, A

u

d

io

 D

u

b

b

in

g,

 and

 Con

nec

tin

g

 a Co

mpu

te

r

Connect the unit and the player using an i.LINK 
cable (not supplied). After turning on the power of 
the unit, set the INPUT SELECT switch on the unit 
to HDV/DV. 

Press the STOP button on the unit to stop the tape.

While holding the DUPLICATE button down, press 
the PLAY button on the unit. 

The unit and the player will automatically rewind 
the tape to the beginning. The unit enters the 
duplicate-standby mode. The player enters the 
playback pause mode. Then the DUPLICATE and 
PLAY indicators on the unit light and the 
duplication starts. 

• Before you start duplication, make sure that the player 

has finished loading the cassette. 

• The duplication starts after the i.LINK connection is 

established so that the first part of the source tape is 
dropped on the copied tape. 

• If the player has functions such as auto repeat, set them 

to OFF.

• If the player has a still timer function, set the still timer 

to the longest time to ensure enough time for 
rewinding the tape to the beginning. 

• When you use a DSR-45 as the player, set the 

REMOTE/LOCAL switch of the DSR-45 to 
[LOCAL]. 

• If you operate the player while duplicating and the 

PLAYER UNCONTROLLABLE warning message 
appears and duplication stops, press the EXEC button 
on the unit to end duplication once, and then repeat the 
procedures.

Connect the unit and the player using an i.LINK 
cable (not supplied). After turning on the power of 
the unit and the player, set the INPUT SELECT 
switch on the unit to HDV/DV.

Locate the points where you want to start playback 
and recording on each tape.

Press the STOP button on the unit.

While holding the DUPLICATE button down, press 
the PLAY button on the unit.

The unit enters the duplicate-standby mode. The 
player enters the playback pause mode. Then the 
DUPLICATE and PLAY indicators on the unit light 
and duplication starts.

To adjust the point where duplication starts, while 
holding the DUPLICATE button down, press the 
PAUSE button and PLAY button in step 4. The unit will 
not start duplication until you press the PAUSE button 
again. After confirming that the PLAYER display has 
changed to [READY] (blinking) on the LCD monitor, 
adjust the duplication start point using the player, then 
press the PAUSE button on the unit to start duplication.

• Before you start duplication, make sure that the player 

has finished loading the cassette.

• The duplication starts after the i.LINK connection is 

established so that the first part of the source tape is 
dropped on the copied tape. Play back the tape a few 
frames before of the portion where you want to begin 
the duplication.

• If the player has functions such as auto repeat, set them 

to OFF. Also, when the player has an auto rewind 
function, set the function to ON.

• You may not be able to duplicate the beginning of the 

source tape. Locate the start of the recorded portion on 
the source tape, and then start duplication.

• If there is a blank portion on the tape, the first part of 

the recorded portion that follows may be dropped on 
the copied tape.

• When the time code on a player operates either 

discontinuously or incorrectly, a difference in frame 
values between the numeric time codes may occur.

Press the STOP button on the unit, and pause 
duplicating.

During the pause, the following confirmation 
display appears.

[ 

X

 ] : 

RESTART

Can adjust star t

position or change

cassette.

[ 

x

 ] : 

END

DUPLICATE PLUS

00:12:34:12