Marantz SA8003 사용자 설명서
10
Names aNd
FuNctIONs
BasIc
cONNectION
BasIc
Opera
tION
adV
aNced
aNced
cONNectIONs
trOuBlesHOOtING
OtHers
BasIc
Opera
tION
ENGLISH
applIca
tION
Opera
tION
BasIc OperatION
NOrmal plaYBacK
super audIO cd plaYer plaYBacK
0
2
7
8
1.
4.
2. 3.
1.
Keep pressing the POWER Switch for about
a second to turn on the system.
Display
The display cycles from TOC Reading →
No Disc (when no disc is loaded) → Super
Audio CD (when the start sound mode
setting is Super Audio CD).
Audio CD (when the start sound mode
setting is Super Audio CD).
2.
Press the
0 button.
The disc tray comes out. Place the disc with
label side up on the tray.
To play a single (8cm) CD, place the disc
with the indentation at the center of the
tray.
tray.
3.
Press
0 button.
Caution:
Do not close the disc tray by pressing it in with your
hand, as this will damage it.
hand, as this will damage it.
4.
Press 2 button.
Disc type is automatically detected and
playback is started. Track number and track
elapsed time (minute, second) appear on
the display.
• For Super Audio CD/CD hybrid-layer
elapsed time (minute, second) appear on
the display.
• For Super Audio CD/CD hybrid-layer
discs (see page 2), the layer that is set
in the start sound mode (see page 16)
is played. To change the layer, use the
S.MODE button (see page 15).
in the start sound mode (see page 16)
is played. To change the layer, use the
S.MODE button (see page 15).
(Exp.:Track 6, Elapsed time 2 min 8 sec)
Number of current track
Minutes Seconds
Playback automatically stops at the end of the final
track.
tO stOp plaYBacK
Press
7 button.
tO eJect dIsc
Press
0 button to open the disc tray and take the
disc off. Press the button again to close the tray.
Disc tray must be closed when the unit is not be
used.
tO pause plaYBacK
Press
8 button.
PAUSE indicator will light and playback is paused
at the point that the button is pressed. To restart
playback, press
8 button again or press 2 button.
plaYING YOur FaVOrIte
tracKs OF a dIsc
0-9
0
2
7
8
¡ ¢
4 1
specIFY tracK NumBer tO plaY
(dIrect searcH)
Specify track number with numerical buttons (0-9)
on the remote controller.
(example)
3rd track : Press 3.
12th track : Press 1 and then press 2 (within
3rd track : Press 3.
12th track : Press 1 and then press 2 (within
approximately 1.5 seconds).
IF a WrONG NumBer Is pressed
If a track number that is not in the disc is specified,
“No Track” will be shown on the main display.
Press correct number again.
sKIppING tO tHe preVIOus Or NeXt
tracK (tracK sKIp)
tracK (tracK sKIp)
tO lIsteN tO a tracK pOsterIOr tO tHe
curreNt tracK
curreNt tracK
Press the
¢ button on the remote controller or
the unit the same number of times as the number
of tracks you want to advance.
tO lIsteN tO a tracK prIOr tO tHe curreNt
tracK
tracK
If the
4 button is pressed on the unit or the
remote controller while playing a track, playback
starts again from the start of the current track.
Continue to press the
4 button for the same
number of times as the number of tracks you want
to return.
plaYING YOur FaVOrIte
parts OF a dIsc (searcH)
0
2
7
8
¡ ¢
4 1
The search is started by holding down the
4, ¢
buttons on the player or the
1, ¡ buttons on the
remote control unit during playback.
The search speed can be changed by pressing the
4, ¢ buttons on the player or the 1, ¡
buttons on the remote control unit.
The search speed changes in 4 steps: 1 → 2 → 3
→ 4 → 1.
4 is the fastest search speed.
When the specific part you wish to hear is near,
press the 2 button.
Note:
No sound is output during the search operation.