JVC LPT0679-001B 사용자 설명서
Masterpage:Right-NoTitle0
59
Filename [SR-VS30EK_3-EN.fm]
Page 59
February 1, 2002 2:04 pm
F
Locate the end point.
G
Prepare the source tape.
Rewind the tape in the DV deck to the beginning of the
scene you want to edit.
scene you want to edit.
H
Prepare the VHS deck for dubbing.
A Press VHS.
B Search for the point where you want to start dubbing
by pressing
4, 5 or 3 then press 8.
C Press 7, then the VHS deck enters the Record Pause
mode.
I
Start Random Assemble Editing.
Press START (or OK).
● Automatic editing begins; all the specified scenes are copied
to the VHS deck in the order they were registered.
● The on-screen display remains while your recorder searches
for each scene (blinking cursor indicates scene currently being
searched for), but disappears during actual editing.
searched for), but disappears during actual editing.
● During scene search, the VHS deck automatically enters its
Record-Standby mode.
● When all registered scenes have been edited, the DV deck
enters the Pause mode, the VHS deck enters its Record Pause
mode, and the arrow blinks at the next available number.
mode, and the arrow blinks at the next available number.
J
End Random Assemble Editing.
Press R.A.EDIT twice to return to the normal screen.
Press
Press
8 to stop the VHS deck’s Record Pause mode.
Press DV, then press
8 to stop the DV deck’s Pause mode.
To Make Corrections ...
... in step 5 or 6, you can cancel registered in and out points by
pressing
pressing
&
. Each time you press, the preceding point is erased.
● If, for example, you have registered 5 sets of in and out points
and want to reset the first set, you have to press
& until all
points after the first set have been erased. Reenter them after
you have repaired the first set of points.
you have repaired the first set of points.
NOTES:
● When Random Assemble Editing does not work, press
,
then perform Random Assemble Editing again.
● To cancel the registered scene, press &. Each time & is
pressed, the latest registered scene is erased.
● When the source tape has more than 2 identical time codes
(
墌
pg. 35), the recorder may not find the edit-in point you set
and a malfunction may occur.
● When choosing a scene, set edit-in and edit-out points so that
there's a relatively large difference between them.
● If the search time for an in-point exceeds 5 minutes, the VHS
deck's Record-Pause mode will be cancelled and editing will
not take place.
not take place.
● If there are blank portions before or after the edit-in and edit-
out points, a blue-backed screen may be included in the
edited version.
edited version.
● Since time codes register time only as accurately as seconds,
the time code total time may not match the total programme
time exactly.
time exactly.
● To use Random Assemble Editing consecutively for two or
more programmes, press START for each programme.
When dubbing from another Mini DV cassette, change the
Mini DV cassette first, and then press START.
When dubbing from another Mini DV cassette, change the
Mini DV cassette first, and then press START.
Press
4 to start playback.
Find the edit-out point where
you want the edited scene to
end by pressing
you want the edited scene to
end by pressing
9, then press
IN/OUT.
● The edit-out point is registered
in memory and appears on the
screen.
screen.
● The total time of the edited
scenes is displayed to the right
of “TOTAL”.
of “TOTAL”.
● Repeat steps 5 and 6 for each
additional scene.
SR-VS30EK_1.book Page 59 Friday, February 1, 2002 2:31 PM