JVC HR-J696EK 사용자 설명서
three step quick start
11
TV PR +
TV PR –
T
V
–
TV
+
TV
0000
STOP
FIN
MENU
OK
TV/VCR
DAILY/QTDN.
VPS/PDC
AUX
?
WEEKLY/HEBDO
PROG
30 SEC
– –:– –
AUDIO
1
2
3
4
6
5
7
8
9
0
DATE
START
DEBUT
DEBUT
PR
2
4
1
3
ENTER/ENTR
EE
EXPRESS
PR +
ENTER/ENTR
EE
OK
3
/
before you start
Check that the VCR is
turned off and no
cassette is inserted
Load the batteries into
the Remote Control
Refer to the Remote
Control diagram
on pages 6–7
Unless indicated
otherwise, use the
buttons on the Remote
Control
Check that the
connection is completed
Be sure to use the fully-
wired 21-pin SCART cable
Turn on the TV whose
channels have already
been stored
Preset Download
START PRESET DOWNLOAD
Press the o button. The display panel on the
front of the VCR will show the word ‘Auto’.
Press the A or B buttons to select
‘CH – –’ and press
front of the VCR will show the word ‘Auto’.
Press the A or B buttons to select
‘CH – –’ and press
OK
3
/
(or E).
what will happen?
The VCR is automati-
cally setting up the tuner channels by down-
loading from your TV, clock and the VIDEO
Plus+ system assigned Guide Program
numbers. During downloading, preset position
on the display panel increases from “CH
loading from your TV, clock and the VIDEO
Plus+ system assigned Guide Program
numbers. During downloading, preset position
on the display panel increases from “CH
1
”.
rf and sc art connection
If the TV set is in its AV mode (see the TV
manual), you will see the following information displayed on your TV screen:
SET THE VIDEO CHANNEL TO OFF
When
Preset Download
has finished, ‘COM-
PLETED’ appears on the TV screen. Press o to
turn off the VCR. Press and hold down S on
the VCR until you will see the display on the
right. Press PR Button on the Remote Control until the figure reads ‘– –’.
turn off the VCR. Press and hold down S on
the VCR until you will see the display on the
right. Press PR Button on the Remote Control until the figure reads ‘– –’.
FINISH PRESET DOWNLOAD
Press
and move on to
Step 2
to check the results.
oops!
If there is a power cut or you accidentally press a button during
P
reset
Download, turn the VCR off and then on again. Re-perform
P
reset Download.
NOTES
• In areas where no TV station transmits the PDC signal, the VCR cannot setup
either the clock or Guide Program numbers.
• On this VCR, the characters available for station names (ID) are A–Z, 0–9, –,
*
, + and (space). The names of some downloaded stations may differ from
those on your TV.
Preset Download is running:
don’t touch any buttons
don’t touch any buttons
VCR
SAT
REVIEW
VCR
SAT
REVIEW
Your TV screen during Preset
Download
Download
T-V LINK
PLEASE WAIT
[MENU]: EXIT
GUIDE PROG SET
PLEASE WAIT
[MENU]: EXIT
VCR
SAT
REVIEW
FINISH AUTO SETUP
Press
and move on to
Step 2
to check the results.
oops!
If there is a power cut or you accidentally press a button during
Auto
Setup
, turn the VCR off and then on again. Re-perform
Auto Setup
.
– –:– –
O
OK
3
/
TV PR +
TV PR –
T
V
–
TV
+
MENU
ENTER/ENTR
EE
TE
PR
OK
3
/
OK
3
/
HR-J695/696EK-EN/p08-12
5/28/02, 11:03 AM
11