JVC SR-MV45U 사용자 설명서

Masterpage:Right+

Filename [SR-MV45_55U_10Editing.fm]

Page 51

January 10, 2007 1:18 pm

You can dub programs from a DV camcorder or DV equipment 
connected to the unit with a DV cable. The unit’s remote control 
allows you the limited control of the connected DV camcorder or 
DV equipment functions during dubbing.

Connect a DV camcorder or DV equipment to the [DV IN] 

connector on the unit’s front panel.

Load a DVD-RAM/RW/R disc on the unit.

Press VCR/DVD repeatedly so that the DVD lamp lights up on 

the unit.

Press INPUT SELECT +/– on the unit or INPUT +/– on the 

remote control to set the input to “DV”.

● The “DV DUBBING” controller appears on the TV screen.

● If “

” does not appear on the “DV DUBBING” controller, make 

sure the DV equipment is connected correctly.

Press REC MODE repeatedly to set the recording mode. 

Locate the point from where you want to start dubbing, then 

stop or pause playback by pressing the following buttons on the 
remote control: 4, 5, 3, 8, 9

● To play back in slow speed (1/10 of the normal speed), press 9 to 

pause playback, then press 3 or 5.

● To play back frame-by-frame, press 9 to pause playback, then press 

9 repeatedly. Each press of 9 advances a frame.

● To change the playback direction, press 3 or 5.

Press w e to select 

, then press ENTER.

Press rt to select the desired 

sound track, then press ENTER.

AUDIO 1

: Select this to record the 

original stereo sound played 
back on the connected DV 
equipment.

AUDIO 2

: Select this to record the 

dubbed stereo sound played 
back on the connected DV 
equipment.

MIX

: Select this to record the sound of both “AUDIO 1” and 

“AUDIO 2”.

● Note that this selection is not available when the source program is 

recorded in 16BIT (48 kHz) mode.

Press w e to select 

, then press ENTER. The 

dubbing starts.

● Playback on the external DV equipment and recording on the unit 

should start simultaneously.

● When the playback from the beginning is not possible, the “DV 

DUBBING” controller cannot be used. Perform dubbing without using 
the “DV DUBBING” controller. (

墌

below)

● To pause dubbing, press w e to select 

, then press 

ENTER. Both the unit and the external DV equipment pause dubbing. 
Pressing 9 on the unit also works the same way.

● To clear the “DV DUBBING” controller from the TV screen, press ON 

SCREEN.

Press 8 on the remote control to stop dubbing.

● Both the unit and the external DV equipment stop dubbing.

● Dubbing copyright guarded programs is not possible.

● Original DV information such as the recording date and time are not 

recorded.

● The superimposed indication during the operation or dubbing is not 

recorded.

● It is not possible to perform dubbing when 

the dubbing (

DUBB.

) 

lamp

 lights up on the unit. Press VCR]DVD so that 

the dubbing 

(

DUBB.

) lamp

 lights off.

Performing dubbing without using the “DV DUBBING” 
controller
A Press INPUT SELECT +/– on the unit or INPUT +/– on the 
remote control to set the input to “DV”.
B Press REC MODE repeatedly to set the recording mode. 
(

C Start playback on the external DV equipment slightly before the 
actual point from where you wish to start dubbing.
D Press 7 on the unit to start recording. Or while holding 7, press 
4 on the remote control. The dubbing starts.
E When the dubbing ends, press 8 on the unit, then stop 
playback on the external DV equipment.

● Use the DV cable VC-VDV 204U for connection.

● When you connect a PC to the [DV IN] connector, we do not 

assure the normal operation of this unit.

To [DV IN]

DV cable

(VC-VDV 204U)

(not supplied)

DV Camcorder

DV connector

Your unit

DV equipment

SR-MV45_55US.book  Page 51  Wednesday, January 10, 2007  1:18 PM