Coleman 2000001588 사용자 설명서

STITCH LINE

Rotate all eight Leg Poles upright and insert pin on 
each web loop at the side locations as shown.
(Fig. 7 & 7A)

7.

Locate the plastic hooks at sides and 
corners of tent, then snap onto Leg 
Poles to attach. (Fig. 8)

Insert plastic stakes through web straps located 
on both sides of tent, then drive in to secure. 
(Fig. 10)
NOTE: It may be necessary to remove metal 
stakes through web straps at side of tent and 
screen room, pull tent taut, and drive in stakes 
to secure.

To stretch tent to finished size:
• Push in button on Leg Pole while 

twisting lower Leg Pole section
counterclockwise (Fig.9);

• Pull up on top Leg Pole section until 

tent is taut;

• Twist the lower Leg Pole clockwise 

until the button locks into the center
or lowest hole;

• Repeat on remaining Leg Poles.

®

Assemble Vertical Door Pole (shorter black pole with plastic tips); 
then insert through zippered vertical pole sleeve on hinged side of 
door. (Fig. 11)

Insert end of Vertical Door Pole into bottom hinge plate, apply
pressure to form a slight bow, then insert other tip of pole into top 
hinge. Zip up vertical pole sleeve. (Fig. 12 & 13)

Assemble Door Pole (longer black pole with plastic cap tips); then 
insert into zippered pole sleeve at top of door. (Fig. 14)

Insert end of Door Pole into top hinge plate, apply pressure to form 
a bow, then insert other tip of pole into the bottom hinge. (Fig. 15)

Zip up pole sleeve to enclose Door Pole. (Fig. 16)

Unfold tent and spread out on a clean, level surface with the door
facing the desired direction. Unzip doors. (Fig. 1)

4.

Assemble eight, steel, shock-corded, Leg
Poles. Push down on steel button on tapered 
end and insert into end with four holes.
NOTE: Make sure steel button locks into
third hole on pole as shown. (Fig.4)

5.

Insert curved end of Leg Poles
(with red marking) into the 
ends of the Ridge Pole
(with red marking). Insert 
curved end of remaining 
short Leg Poles into the
ends of the remaining
Ridge Poles. (Fig. 5 & 6)

2.

Pull four corners of tent taut, then secure by 
driving stakes through web loops at an angle for
better anchoring. (Fig. 2)

3.

Assemble four, steel, shock-corded, curved 
Ridge Poles. Insert Ridge Poles (with red 
marking) into center sleeves on top of tent 
with the red trim (Fig. 3). Insert the remain-
ing curved Ridge Poles into the other two 
sleeves on top of tent.

(continued on other side)

Long Leg Pole, steel

(w/ red marking)

4

19mm

N/A

5010000608

Short Leg Pole, steel

4

19mm

N/A

5010000610

Curved Ridge Pole, steel 

(w/ red marking)

2

19mm

N/A

5010000607

Curved Ridge Pole, steel

2

19mm

N/A

5010000609

Awning Pole, black,

fiberglass, metal tips

1

6.3mm

5010000543

5010000545

Door Pole, long, thin, black,

fiberglass, rubber tips

1

6.3mm

5010000543

5010000545

Vert. Door Pole, short, black,

fiberglass, rubber tips

1

6.3mm

5010000543

5010000545

Read all instructions before set up.
• Select a level site clear of rocks, branches, and other hard or sharp 

objects, to install your tent.

•  Do not set up your tent under trees because of potential lightning strikes

or falling tree limbs in inclement weather.

• Secure with all stakes and guylines provided to prevent property damage

or personal injury.

•  For best results in windy conditions, position narrow end of tent into

the wind.

•  Enlist the help of at least one other person to assist you when it is time 

to assemble the tent.

Red

1

360mm

5010000624

Green

3

610mm

5010000627

Orange

2

670mm

5010000628

CAUTION: “Springs” may have sharp edges. Handle with care to avoid
injury. Keep out of reach of children.