ZTE Z930L 사용자 설명서

54

55

This model phone meets the government’s requirements 
for exposure to radio waves. 
This phone is designed and manufactured not to exceed 
the emission limits for exposure to radio frequency (RF) 
energy set by the Federal Communications Commission 
of the United States, Industry Canada of Canada.
During SAR testing, this device is set to transmit at its 
highest certified power level in all tested frequency 
bands, and placed in positions that simulate RF 
exposure in usage against the head with no separation, 
and near the body with the separation of 0.4 inches  
(10 mm). Although the SAR is determined at the 
highest certified power level, the actual SAR level of the 
device while operating can be well below the maximum 
value. This is because the phone is designed to operate 
at multiple power levels so as to use only the power 
required to reach the network. In general, the closer you 
are to a wireless base station antenna, the lower the 
power output.
The exposure standard for wireless devices employs a 
unit of measurement known as the Specific Absorption 
Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg, 
and 1.6 W/kg by Industry Canada.
This device is compliance with SAR for general 
population/uncontrolled exposure limits in ANSI/IEEE 
C95.1-1992 and Canada RSS 102, and had been tested 
in accordance with the measurement methods and 

procedures specified in OET Bulletin 65 Supplement C, 
and Canada RSS 102. This device has been tested, and 
meets the FCC, IC RF exposure guidelines when tested 
with the device directly contacted to the body.
The FCC has granted an Equipment Authorization for 
this model phone with all reported SAR levels evaluated 
as in compliance with the FCC RF exposure guidelines. 
SAR information on this model phone is on file with the 
FCC and can be found under the Display Grant section 
of www.fcc.gov/oet/ea/fccid after searching on FCC 
ID: SRQ-Z930L.
For this device, the highest reported SAR value for 
usage against the head is 0.78 W/kg, for usage near 
the body is 1.17 W/kg.
While there may be differences between the SAR levels 
of individual Z930L phones and at various positions, 
they all meet the government requirement.
SAR compliance for body-worn operation is based on 
a separation distance of 0.4 inches (10 mm) between 
the unit and the human body. Carry this device at least 
0.4 inches (10 mm) away from your body to ensure RF 
exposure level compliant or lower to the reported level. 
To support body-worn operation, choose the belt clips 
or holsters, which do not contain metallic components, 
to maintain a separation of 0.4 inches (10 mm) 
between this device and your body.
RF exposure compliance with any body-worn accessory, 
which contains metal, was not tested and certified, and 
using such body-worn accessory should be avoided.

This device complies with part 15 of the FCC Rules. 
Operation is subject to the following two conditions: 
(1) This device may not cause harmful interference, and 
(2) this device must accept any interference received, 
including interference that may cause undesired 
operation.

 Changes or modifications not expressly 

approved by the manufacturer could void the user’s 
authority to operate the equipment.

 This equipment has been tested and found 

to comply with the limits for a Class B digital device, 
pursuant to part 15 of the FCC Rules. 
These limits are designed to provide reasonable 
protection against harmful interference in a residential 
installation. This equipment generates, uses and can 
radiate radio frequency energy and, if not installed and 
used in accordance with the instructions, may cause 
harmful interference to radio communications. However, 
there is no guarantee that interference will not occur in 
a particular installation. If this equipment does cause 
harmful interference to radio or television reception, 
which can be determined by turning the equipment 
off and on, the user is encouraged to try to correct the 
interference by one or more of the following measures:
•  Reorient or relocate the receiving antenna.
•   Increase the separation between the equipment and

receiver.

•   Connect the equipment into an outlet on a

circuit different from that to which the receiver is 
connected.

•   Consult the dealer or an experienced radio/TV

technician for help.

Your Z930L is compliant with the FCC Hearing Aid 
Compatibility (HAC) requirements. For additional HAC 
information, including the HAC rating of this product, 
please refer to www.zteusa.com/support_page/.
When some wireless phones are used near some 
hearing devices (hearing aids and cochlear implants), 
users may detect a buzzing, humming, or whining 
noise. Some hearing devices are more immune than 
others to this interference noise, and phones also 
vary in the amount of interference they generate. The 
wireless telephone industry has developed ratings for 
some of their mobile phones to assist hearing device 
users in finding phones that may be compatible with 
their hearing devices. Not all phones have been rated. 
Phones that have been rated have a label on the box. 
Your Z930L has been tested for hearing aid 
device compatibility and has an M3/T4 rating.
These ratings are not guaranteed. Results will vary, 
depending on the level of immunity of your hearing 
device and the degree of your hearing loss. If your 
hearing device happens to be vulnerable to interference, 
you may not be able to use a rated phone successfully.