Mirage Loudspeakers OMNI 50 사용자 설명서

owners manual

A general guideline for the recommended height would be approximately 6
feet. But, there might be situations when this is not possible. If an OMNI
series speaker is installed on the wall above six feet, position it so the grille
faces downward. If the OMNI series speaker is positioned below six feet,
position it so the grille faces upward.

CEILING MOUNT

The OMNI FX can be ceiling mounted by using the Macromount bracket and
NOT the wall mount clip provided. The OMNI FX, OMNI 50, OMNI 60 and
OMNI CC are equipped with an insert to accommodate the optional
Macromount bracket for ceiling mount options. The versatile Macromount
bracket provides the sturdiest ceiling mount and its terminal fits the 3/8”-16
thread insert located at the back of the OMNI models mentioned. Just
remove the rubber Mirage logo on the input terminal in back of the speaker
to expose the insert.

Orient the speaker so the OMNITECH module, or portion of the speaker
that houses the drivers, faces the listening area.

BOOKSHELF/ENTERTAINMENT UNIT PLACEMENT

The small size and Omnipolar dispersion of the versatile OMNI 50, OMNI 60
and OMNI CC center channel speakers permits them to be easily placed,
among other places, in a bookshelf. If this is your preferred placement, affix
the isolating pads provided to the bottom of the speaker to help isolate the
speaker from the shelf and eliminate any transference of resonance. To
maximize the Omnipolar dispersion potential, bring the speaker as close to
the front of the cabinet as possible.

FEET

The OMNI 250 and OMNI 260 come equipped with a foot kit to improve
the bass performance of your speaker. This kit should include:

2 - Front Feet

2 - Round head machine bolts

4 - Nuts

2 - Regular length Spikes for the front feet

2 - Adhesive rear feet

2 - Very long spikes for the rear feet

4 - 1” wood screws

4 - washers

4 - Rubber bumpers

1 - Spacer-supplied only with the OMNI 260

Follow these instructions to attach the feet
to your speaker: See diagram 2.

Lay the speaker on it’s back and position the front feet over the
pre-drilled holes.

Insert the 2 round head machine bolts into the two larger holes,
one in each foot

If you have the OMNI 260, place the spacer in the open area
between the two feet

Insert the four wood screws into the smaller holes, two in each foot.
For the OMNI 260, these screws will also secure the spacer.

To attach the rear feet, first thread a nut onto the very long spike, then
slide a washer over the shaft of the spike so it rests on the nut. Then,
insert the spike through the foot. Once properly located over the
insert where the spike will fit, remove the adhesive backing on the foot
and attach it to the speaker.

You may now attach either the regular length spikes to the front
feet,preferred on carpeted floors or the rubber bumpers preferred for
wood or other potentially easily damaged surfaces.

Place the speaker upright and repeat for the second speaker.

The OMNI 50, OMNI 60, OMNI FX and OMNI CC are equipped with
rubber isolation feet. Remove the adhesive backing on these feet and attach
them to the bottom of the speaker.

CONNECTIONS

The Mirage OMNI series is equipped with high quality binding posts that
permit the use of banana plugs, spades, or a bare wire connection. Turn them
counterclockwise to loosen, clockwise to tighten.

Connect the speaker wire from the positive (RED +) terminal on the amp to
the positive (RED+) terminal on the speaker. Connect the negative
(BLACK-) terminal on the amplifier to the negative (BLACK-) terminal
on the speaker. See diagram 1.

OMNI 260

System Type:

Magnetically Shielded Omnipolar Tower

Frequency Response:

35Hz-20KHz, +/- 3dB

Tweeter:

1” (25mm) PTH™ Pure Titanium Hybrid

Woofer:

Two 6

“ Polypropylene Titanium Deposit Hybrid

Crossover Points:

2KHz

Room Efficiency:

93dB

Impedance:

8-ohms nominal, 4-ohms minimum

Recommended
Amplifier Power:

Up to 200-watts RMS/Channel

Inputs:

High Quality 5-way Terminals

Dimensions:

in. 42 x 9 x 15

H x W x D

cm. 107 x 23 x 38

Finishes:

Black and cherry

Weight:

55 lbs / speaker
25 kg / speaker

OMNI 250