Buffalo Tools DP5UL 사용자 설명서
DP5UL 5 Speed Drill Press Assembly & Operating Instructions
12
REMOVING THE CHUCK
To remove the chuck, pull the spindle down fully, using the feed handles. The slot in the side of the Quill
will become visible. Note the position of the chuck, perhaps by placing a chalk mark, in line with the
chuck, on the column, then raise the table so that it is only an inch or so below the position marked.
Place a thick cloth, or similar material, on the table to catch the chuck, to prevent damage when it drops.
Pull down the spindle once more, until the slot in the Quill tube is visible. lnsert the drift wedge into the slot
and give it a sharp tap, preferably with a copper hammer. This will break the seal between the quill tube
and the arbor, allowing the chuck to fall free, on to the cloth on the table. To disconnect the chuck from
the arbor, give it a sharp rap with a soft head mallet to break the taper seal.
NOTE: Morse taper drills (MTS), may also be used with this machine, and are inserted into the Quill to
replace the arbor. Removal is the same as that for removing the chuck.
Maintenance
DISCONNECT THE POWER SUPPLY BEFORE CLEANING. WEAR SAFETY EYEWEAR BEFORE
CLEANING. USED COMPRESSED DRY AIR TO BLOW OFF DUST AND DEBRIS. USE A SOFT BRISTLE
BRUSH IF COMPRESSED AIR IS NOT AVAILABLE.
CLEANING. USED COMPRESSED DRY AIR TO BLOW OFF DUST AND DEBRIS. USE A SOFT BRISTLE
BRUSH IF COMPRESSED AIR IS NOT AVAILABLE.
APPLYING EXCESSIVE FORCE TO THE TOOL CAN OVERLOAD THE MOTOR, DECREASE THE LIFE
AND INCREASE THE WEAR ON THE TOOL.
AND INCREASE THE WEAR ON THE TOOL.
SOME CHEMICALS CAN DAMAGE THE PRODUCT. DO NOT USE HARSH CHEMICALS SUCH AS
GASOLINE, CARBON TETRACHLORIDE, PAINT THINNER, ETC.
GASOLINE, CARBON TETRACHLORIDE, PAINT THINNER, ETC.
A QUALIFIED REPAIR TECHNICIAN MUST PERFORM ANY TOOL SERVICE OR REPAIR. SERVICE OR
MAINTENANCE PERFORMED BY UNQUALIFIED PERSONNEL COULD RESULT IN INJURY. USE ONLY
IDENTICAL REPLACEMENT PARTS. USE OF UNAUTHORIZED PARTS OR FAILURE TO FOLLOW
MAINTENANCE INSTRUCTIONS MAY CREATE A RISK OF ELECTRIC SHOCK OR INJURY.
MAINTENANCE PERFORMED BY UNQUALIFIED PERSONNEL COULD RESULT IN INJURY. USE ONLY
IDENTICAL REPLACEMENT PARTS. USE OF UNAUTHORIZED PARTS OR FAILURE TO FOLLOW
MAINTENANCE INSTRUCTIONS MAY CREATE A RISK OF ELECTRIC SHOCK OR INJURY.
DO NOT MAKE CONTACT WITH A GROUNDED SURFACE WHILE USING DRILL PRESS. CONTACT
WITH SURFACES LIKE PIPES, RADIATORS OR MAJOR APPLIANCES INCREASE YOUR RISK OF
ELECTRIC SHOCK.
WITH SURFACES LIKE PIPES, RADIATORS OR MAJOR APPLIANCES INCREASE YOUR RISK OF
ELECTRIC SHOCK.
The Drill Press must be properly maintained for maximum performance. Always inspect before use. Any
damage should be repaired, and faults rectified. Please refer to the troubleshooting chart. If you are
unable to correct any problems, please contact customer service.
Monthly (When in constant use)
1. Check tightness of mounting bolts, and head and column securing set screws.
2. Check belt for wear and replace if frayed or damaged in any way.
3. Blow out any dust that may have accumulated in the motor fan.
4. Apply a thin coat of wax paste or light oil to the column for lubrication and to help prevent corrosion.
Lubrication
All bearings are packed with grease at the factory and require no further lubrication.
damage should be repaired, and faults rectified. Please refer to the troubleshooting chart. If you are
unable to correct any problems, please contact customer service.
Monthly (When in constant use)
1. Check tightness of mounting bolts, and head and column securing set screws.
2. Check belt for wear and replace if frayed or damaged in any way.
3. Blow out any dust that may have accumulated in the motor fan.
4. Apply a thin coat of wax paste or light oil to the column for lubrication and to help prevent corrosion.
Lubrication
All bearings are packed with grease at the factory and require no further lubrication.