Optimus S1000PJ 사용자 설명서
151
Caring for the Camera
T
e
chni
cal N
o
te
s
Cleaning
Do not use alcohol, thinner, or other volatile chemicals.
Storage
Turn the camera off when not in use. Be sure that the power-on lamp is off before
putting the camera away. Remove the battery if the camera will not be used for an
extended period. Do not store the camera with naphtha or camphor moth balls, or
in any of the following locations:
• Next to equipment that produces strong electromagnetic fields, such as
putting the camera away. Remove the battery if the camera will not be used for an
extended period. Do not store the camera with naphtha or camphor moth balls, or
in any of the following locations:
• Next to equipment that produces strong electromagnetic fields, such as
televisions or radios
• Exposed to temperatures below –10 °C (14 °F) or above 50 °C (122 °F)
• Places that are poorly ventilated or subject to humidity of over 60%
• To prevent mold or mildew, take the camera out of storage at least once a
• Places that are poorly ventilated or subject to humidity of over 60%
• To prevent mold or mildew, take the camera out of storage at least once a
month. Turn the camera on and release the shutter a few times before putting
the camera away again.
the camera away again.
C
Notes on the Monitor
• The monitor may contain a few pixels that are always lit or that do not light. This is a characteristic
common to all TFT LCD displays, and does not indicate a malfunction. Images recorded using the
product will not be affected.
product will not be affected.
• White or colored streaks of light may be visible in the monitor with framing of bright subjects. This
phenomenon, known as “smear,” occurs when extremely bright light strikes the image sensor. This
is due to characteristics of the image sensor and does not indicate a malfunction. Smear may also
cause partial discoloration in monitor display with shooting.
Smear does not affect recorded images except when shooting with
is due to characteristics of the image sensor and does not indicate a malfunction. Smear may also
cause partial discoloration in monitor display with shooting.
Smear does not affect recorded images except when shooting with
Continuous set to Multi-
shot 16 and when recording movies. When shooting in these modes, avoiding bright objects
such as the sun, reflections of the sun, and electric lights is recommended.
such as the sun, reflections of the sun, and electric lights is recommended.
• Images in the monitor may be difficult to see under bright lighting.
• The monitor is lit by an LED backlight. Should the monitor begin to dim or flicker, contact your
• The monitor is lit by an LED backlight. Should the monitor begin to dim or flicker, contact your
Nikon-authorized service representative.
Lens/
projector
window
projector
window
Avoid touching the lens/projector window with your fingers. Remove dust or
lint with a blower (typically a small device with a rubber bulb attached to one
end that is pumped to produce a stream of air out the other end). To remove
fingerprints or other stains that cannot be removed with a blower, wipe the
lens/projector window with a soft cloth, using a spiral motion that starts at the
center of them and working toward the edges. If this fails, clean them using a
cloth lightly dampened with commercial lens cleaner.
lint with a blower (typically a small device with a rubber bulb attached to one
end that is pumped to produce a stream of air out the other end). To remove
fingerprints or other stains that cannot be removed with a blower, wipe the
lens/projector window with a soft cloth, using a spiral motion that starts at the
center of them and working toward the edges. If this fails, clean them using a
cloth lightly dampened with commercial lens cleaner.
Monitor
Remove dust or lint with a blower. To remove fingerprints and other stains,
clean the monitor with a soft, dry cloth, being careful not to apply pressure.
clean the monitor with a soft, dry cloth, being careful not to apply pressure.
Body
Use a blower to remove dust, dirt or sand, then wipe gently with a soft, dry
cloth. After using the camera at the beach or other sandy or dusty
environment, wipe off any sand, dust or salt with a dry cloth lightly dampened
with fresh water and dry thoroughly. Note that foreign matter inside the
camera could cause damage not covered by the warranty.
cloth. After using the camera at the beach or other sandy or dusty
environment, wipe off any sand, dust or salt with a dry cloth lightly dampened
with fresh water and dry thoroughly. Note that foreign matter inside the
camera could cause damage not covered by the warranty.