Panasonic AJ-PX5000G 사용자 설명서

– 78 –

[SDI OUT2]

—

Displays the status of the signal output from the <SDI OUT2> terminal.

[OUTPUT]

Displays the status of [MEM]/[CAM] or [OFF] set by [SDI OUT2] and [MONITOR OUT 

MODE] in the main menu → [I/F SETUP] → [OUTPUT SEL].

[SELECT]

Displays the signal format set by [SDI2/HDMI OUT] and [1080P SDI2/HDMI OUT] in the 

main menu → [I/F SETUP] → [OUTPUT SEL] by [SYSTEM]/[DOWNCON]/[1080i].

[CHAR]

Displays the position of the <MON OUT CHARATER> switch by [ON]/[OFF].

[P2CARD STATUS]

—

Displays the status of the P2 card inserted in the card slot, remaining capacity and total 

used capacity.

The statuses of cards to be displayed are as follows:

[ACTIVE]/[ACCESSING]/[INFO READING]/[FULL]/[PROTECTED]/[NOT SUPPORTED]/

[FORMAT ERROR]/[AUTH NG]/[REC IMPOSSIBLE]/[NO CARD]

[TOTAL P2/mP2]

Displays the remaining capacity/total capacity totaled for slots 1/2 (or slots 3/4) and the 

recording medium ([P2] or [mP2]).

[SLOT1] or [SLOT3]

Displays the status of the P2 card in slot 1 (or slot 3) and remaining capacity/total capacity.

[SLOT2] or [SLOT4]

Displays the status of the P2 card in slot 2 (or slot 4) and remaining capacity/total capacity.

[PROXY]

[MEDIA]

Displays the media selection status for proxy recording.

[P2]/[P2&SD]/[OFF]

[MODE]

Displays the setting status for proxy recording mode.

[STD 2CH MP4]/[SHQ 2CH MOV]/[HQ 4CH MOV]/[HQ 2CH MOV]/[LOW 2CH MOV]

[SUPER]

Displays the superimposed setting status of the time code.

[UPPER]/[LOWER]/[OFF]

[PROXY ERROR]

Displays the operation error on the proxy module.

Displays audio settings and the selection status of each recording channel.

[SAMPLE RES]

—

Displays the number of audio recording bits.

[MIC POWER (MENU)]

—

Displays the menu setting status of power supply to the microphone.

[FRONT]

Displays the power supply status to the front microphone currently set in the main menu → 

[I/F SETUP] → [MIC/AUDIO] → [FRONT MIC POWER] by [ON]/[OFF].

[REAR]

Displays whether to set supply of power to the microphone on the <AUDIO IN> terminal at 

the rear in the main menu → [I/F SETUP] → [MIC/AUDIO] → [REAR MIC POWER].

 

f

[OFF]: Power is not supplied to the microphone.

 

f

[ON]: Power is supplied to the microphone when the <LINE>/<MIC> selector switch is set 

to <MIC> and the microphone input power selector switch is set to <+48V>.

[VR SELECT]

—

Displays which of [CH1/2] and [CH3/4] the audio level adjustment dial is to be set as 

enabled to in the main menu → [I/F SETUP] → [MIC/AUDIO] → [VR SELECT].

[LEVEL]

[CH1/2/3/4]

Displays the recording level adjustment method currently selected on each channel.

 

f

[VR]: Displayed when manual adjustment using the adjustment dial is set.

 

f

[MENU]: Displayed when manual adjustment using [LVL CONTROL CH3(CH1)]/[LVL 

CONTROL CH4(CH2)] is set in the main menu → [I/F SETUP] → [MIC/AUDIO].

 

f

[AUTO]: Displayed when automatic adjustment is set.

[F.VR]

[CH1/2/3/4]

Displays by [ON]/[OFF] whether the <F.AUDIO LEVEL> dial is enabled on the channel to 

which [VR] (manual adjustment by adjustment dial) is displayed in [LEVEL].

[A.IN]

[CH1/2/3/4]

Displays the input status of each channel by [FRONT] (front)/[REAR] (rear)/[W.L.] 

(wireless).

[METER]

[CH1/2/3/4]

Displays the recording level of each channel.

Displays the operation status or information of CAC.

[CAC CONT]

Displays the operation status of CAC.

 

f

[ON]: [ON] is set to in the main menu → [MAINTENANCE] → [CAC ADJ] → [CAC CONTROL], and CAC is active.

 

f

[STOP]: [ON] is set to in the main menu → [MAINTENANCE] → [CAC ADJ] → [CAC CONTROL], however, CAC operation 

stops under certain data or lens conditions.

 

f

[OFF]: [OFF] is set to in the main menu → [MAINTENANCE] → [CAC ADJ] → [CAC CONTROL], and CAC is not active.

[CAC MODE]

Displays the operation mode of CAC.

 

f

[AUTO]: The CAC file is automatically selected.

[CONNECT LENS TYPE]

Displays the lens ID of the currently connected digital lens.

[SELECT FILE TITLE]

Displays the title and the file version of the CAC file currently used in the operation. The CAC file can be set in the main menu 

→

 [MAINTENANCE] → [CAC ADJ].

[CAC WARNING]

Displays a warning when operation of CAC has stopped.

 

f

[CAC LENS DATA INVALID]: This is displayed, for example, when the response data from the lens is not supported.

 

f

[LENS INIT. NOT COMPLETED]: This is displayed, for example, when initialization of the lens cannot complete.