DMP Electronics XR500 사용자 설명서

18

6.7 

STRIKE TIME:  

5

This option displays if DOOR is selected as Device Type.

Enter a door access time, between 1 and 250 seconds, during which a keypad or access 

control device relay is activated.  Magnetic locks or electric door strikes are connected 

to the relay and released for the length of the strike time.  Default is 5 seconds.

Enter 0 (zero) to activate the device relay with a toggle action. This allows the user

to activate 

or deactivate the device relay each time a valid user code is entered.  

The device relay is activated 

or deactivated until a user code is entered again.

Note: The Request to Exit door access time of a keypad or Model 733 Wiegand

Interface Module is not affected by this selection.  It remains at 5 seconds.

6.8 

STRIKE DELAY: 

This option displays if DOOR is selected as Device Type.

Enter the number of minutes, 0 to 9, to delay a door strike after a valid code is entered

or a card read occurs. When a valid code or card read or code is received, the activation

of the door strike is delayed for the number of minutes programmed.  The standard door 

strike message is sent to the Central Station receiver and logged in the Display Events at 

the time of card read or code entry and is not delayed.  During this delay, all subsequent 

codes entered or cards presented to the reader for a door strike are ignored and no 

record of the attempt is stored. Enter 0 (zero) to disable. Default is 0 (zero).

6.9 

FIRE EXIT   NO  YES

Select 

YES to allow the door access relay at this address to be released whenever 

Fire panic keys are pressed or a Fire or Fire Verify zone alarm is in the Status List.

The relay is reset whenever a Sensor Reset is performed to remove all Fire and Fire 

Verify zone alarms from the Status List. Select

NO to not allow the door access relay 

at this address to be released.

OUT GROUP  NO  YES

Select 

YES to allow the output group (relays) assigned to the user profile to turn ON

when the device relay is activated for the programmed strike time.  This could be 

used to operate an elevator control.  Default is 

NO.  See the User Profiles section in 

the Appendix of this document for more information about profiles.

OVERRIDE   NO  YES

Use this option to allow door ON/OFF schedules to be overridden by the armed

condition of the system.  Selecting 

YES causes the on time for a door schedule to be 

ignored when all areas assigned to Access Areas for this device are armed.  Should 

any area become disarmed after the door schedule on time, the device output turns 

on.  A door output which is on during a disarmed period automatically turns off when 

all access areas assigned to the device become armed, even if the scheduled off 

time has not been reached.  This feature can be used to keep doors locked when a 

factory opens late, or is forced to close early, due to a snow storm or other cause.  

Select 

NO to allow door schedules to operate independent of system armed status.

Note: When OVERRIDE is YES and there are no areas programmed in ACCESS AREAS, 

the door schedule for that device does not work.  Either set 

OVERRIDE to NO or 

enter an area number in 

ACCESS AREAS. 

AUTO FORCE ARM

DEVICE?   NO  YES  Select YES to have all Display Areas assigned to this keypad automatically arm and 

force arm faulted zones at arming.  The user is not prompted to select areas to 

arm or force arm faulted zones after choosing ARM at the keypad.  If Closing Code 

is programmed as 

YES, only the matching areas between the Display Areas and 

the User Code’s authorized areas arm.  Also, when 

YES is selected, the user is not 

prompted to select areas to disarm after entering a code at Entry Delay or after 

choosing Disarm at the keypad.  All matching areas assigned to the User Code and to 

this keypad are automatically disarmed. When

NO is selected, the user is prompted 

to select areas (ALL NO YES) and choose to force arm or bypass at arming and

disarming.  Default is 

NO.

DOOR  REAL-TIME

STATUS?  

NO  YES  Select YES to have real-time door status messages sent to PC Log reporting and Entré

reporting for this device.  Messages are sent anytime the panel turns the door relay on or 

off. Default is 

NO.

SEND  DOOR  FORCED

MESSAGE?   NO  YES  Select YES to have the panel send a real-time door status message of Forced Open (FO)

to PC Log reporting and Entré reporting when the door relay is off, but the door zone has
transitioned from its normal state.  Default is 

NO.