DMP Electronics XR500 사용자 설명서

30

For example, when Spanish is selected at a keypad, the User Menu and Status List

text display in Spanish at 

that keypad. When the user later accesses the keypad,

pressing the COMMAND key once displays the option for English, Spanish, or French.

Pressing the COMMAND key again continues to display the Status List text in Spanish.

Later on, if English or French is selected at

that keypad, the User Menu and Status 

List text display in the selected language at

that keypad.   

NONE  ENG  SPN  FRN

Select the secondary user language. 

NONE = No secondary language options are displayed 

ENG = English (ENGLISH) 

SPN = Spanish (ESPANOL) 

FRN = French (FRANCAIS)

BYPASS LIMIT  

Enter the maximum number of zones (0 to 8) that can be bypassed in any single area

when that area is being armed at a keypad.  If more zones than the limit are in a 

non-normal state or already bypassed at arming, arming does not occur and Arming

Stopped displays.  The Bypass limit does not affect auto arming or keyswitch arming.  

Entering 0 (zero) allows no limit. Default is 0 (zero).

 

CARD PLUS PIN:

 

  NO YES

Select YES to require all users to present a proximity credential and enter a PIN 

number wherever user code entry is required for system functions accessed from a 

keypad. Select NO to disable Card Plus PIN operation. Default is NO.
Note: The Card Plus PIN option is not designed to operate with All/Perimeter or

Home/Sleep/Away systems.
For an XR500E system using Card Plus PIN, two code entries are required by a user to 

operate the system from a keypad. The first must be a code entered from a Wiegand

interface device (card, fob, etc.) using a reader such as the built-in reader of a DMP

Keypad. An external reader may also be used. The second code (User Pin) is keyed

in at the keypad or could be a second card or fob.
For a Card Plus PIN system, user codes (Card and PIN) are typically administered

using DMP System Link software.
When this option is first turned on at a keypad, the factory default (user number

9999, user code 99) must be available to enter the user menu at a keypad to then

add user codes and PIN numbers or to change existing users to add their PIN number. 

If user 9999 was previously removed, re-enter this user and then set Card Plus

Pin = YES. Afterwards, user 9999 can be removed and the system only allows card

plus PIN entries.
Note: Current users of an existing system are immediately affected in that they must 

have their user code information changed to add the user PIN.

 

WIRELESS

HOUSE CODE: 0

When using a DMP wireless system, enter a house code between 1 and 50. When

using FA Series wireless enter 99. See Wireless programming in Zone Information.

Default is 0 indicating no wireless system is being used.  
The DMP house code identifies the panel, DMP receiver, and DMP transmitters to

each other. When operating, the DMP receiver listens for transmissions that have

the programmed house code and transmitter serial number.  
Note: The flexibility of DMP two-way wireless operation allows an existing house

code to be changed in the panel at any time.  The transmitters may take up to two 

minutes to learn the new house code and continue operation. 
Note: When any wireless zone programming is changed in the panel, wireless

receiver zone programming is updated.  At that point, all wireless zones display as 

normal for approximately 1 minute, regardless of the actual state of the zone.

 

DETECT WIRELESS

JAMMING:  NO YES

This option displays when the House Code entered is for a DMP 1100 Series Wireless

system (1-50). When enabled and the wireless receiver detects jamming, a trouble

or alarm message displays in the Status List and is sent to the central station

receiver. Select YES to enable jamming messages to display in the Status List.

Select NO to disable jamming messages. Default is NO.