Vermont Casting 1610 사용자 설명서
22
Defiant 1610 Non-Catalytic Woodburning Stove
30002850
The Defiant Controls
Two controls regulate the performance of the Defiant: a
primary air control supplies oxygen for the fire, and a
damper directs air flow within the stove to activate and
deactivate the catalytic combustor. (Fig. 27)
Symbols cast into the stove are reminders of the correct
directions for using the controls. The words ‘Left’ and
‘right’ in these directions are facing the stove.
primary air control supplies oxygen for the fire, and a
damper directs air flow within the stove to activate and
deactivate the catalytic combustor. (Fig. 27)
Symbols cast into the stove are reminders of the correct
directions for using the controls. The words ‘Left’ and
‘right’ in these directions are facing the stove.
Operation
ST541
Defiant
front view
controls
11/00
Griddle Handle
Door Handle
Air
Control
Lever
Ash Door Handle
ST541
Door Handle
Holder
(Behind
Leg)
Andiron
Damper
Handle
Fig. 27 The Defiant’s controls are conveniently located and
easy to operate.
easy to operate.
A Single Air Control Regulates
Heat Output and Burn Time
The primary air control lever, on the right side of the
stove, controls the amount of incoming air for starting,
maintaining, and reviving a fire.
stove, controls the amount of incoming air for starting,
maintaining, and reviving a fire.
More air entering the stove makes the fire burn hotter
and faster, while less air prolongs the burn at a lower
heat output level. (Fig. 28)
For the greatest air supply and maximum heat output
(but the shortest burn time), move the lever toward the
front of the stove. For a fire that will last longer with
less heat, move the lever toward the rear of the stove.
and faster, while less air prolongs the burn at a lower
heat output level. (Fig. 28)
For the greatest air supply and maximum heat output
(but the shortest burn time), move the lever toward the
front of the stove. For a fire that will last longer with
less heat, move the lever toward the rear of the stove.
� � � � � � �
D E F I A N T
� � � � � � �
D E F I A N T
� � � � � � �
D E F I A N T
ST541
thermostat
settings
11/00
Low Heat
Range
Air Control Positions
Medium Heat
Range
High Heat
Range
ST542
Fig. 28 The handle also may be positioned anywhere be-
tween the two extremes for different heat levels.
tween the two extremes for different heat levels.
Fan Kit Installation
1. Attach the fan assembly at the bottom edge of the in-
ner back with two (2) 1/4-20 x 3/4” hex head screws.
2. Attach snapstat to the mounting holes on the un-
derside of the bottom with two (2) 1/4-20 pan head
screws.
screws.
3. Attach the rheostat holder (provided with the stove)
under the right front wing of the bottom heat shield
with two (2) #10 sheet metal screws.
with two (2) #10 sheet metal screws.
4. Attach the rheostat to its holder by inserting the rheo-
stat control shaft through the holder hole. Install the
retaining ring and rheostat knob onto the shaft.
retaining ring and rheostat knob onto the shaft.
5. Secure the rheostat cable to the underside of the
bottom heat shield using the wire tie provided and
the hole at the right rear edge of the heat shield.
the hole at the right rear edge of the heat shield.
6. Fan will not operate until stove reaches approximate-
ly 109°F.
Fig. 26 Fan installation (Kit # 2767).
�����
�����������
����
�����������
����
Rheostat
Knob
Rheostat
Snapstat
Screws
ST848
Hole for Wire
Tie to Secure
Cable
Rheostat
Holder