Vermont Casting SDFBDVR 전단
Stardance Firebox and
Stove Shell/Door
Stove Shell/Door
Installation Instructions
for Models:
SDFBVT/SDFBVTC,
SDFBDVR/SDFBVRC
SDFBVT/SDFBVTC,
SDFBDVR/SDFBVRC
To complete installation of your Stardance gas stove,
you must first assemble the outer cast shell. Follow
the directions for each model. Refer to Homeowner’s
Manual for complete installation instructions.
you must first assemble the outer cast shell. Follow
the directions for each model. Refer to Homeowner’s
Manual for complete installation instructions.
Unpacking the Shell
The Stardance shell is comprised of three cast iron
plates plus the front with operable doors. The top plate
for the top vent models is a single piece. The top plate
for the rear vent models has three (3) pieces, the plate,
screen and grate. Compare parts recieved with those
shown in Figures 1 & 2. Carefully inspect all parts and
immediately report any damaged or missing parts to
your dealer/distributor.
plates plus the front with operable doors. The top plate
for the top vent models is a single piece. The top plate
for the rear vent models has three (3) pieces, the plate,
screen and grate. Compare parts recieved with those
shown in Figures 1 & 2. Carefully inspect all parts and
immediately report any damaged or missing parts to
your dealer/distributor.
ST470
Stardance
shell assy
9/28/00
Side
Rib
Wingbolt
Left
Side
Steel
Tabs
Wingbolt
Rear Skirt
ST470
Fig. 3 Attach rear skirt to the left side.
30004220 7/07 Rev. 0
Assembly Instructions
1. Attach the rear skirt to the left side by aligning the
key holes with the two wingbolts in the side. If nec-
essary, turn the wingbolts to orient the blades verti-
cally. (Fig. 3) Slide the skirt downward to engage it
behind two washers on the side plate bolts and then
tighten both wingbolts.
essary, turn the wingbolts to orient the blades verti-
cally. (Fig. 3) Slide the skirt downward to engage it
behind two washers on the side plate bolts and then
tighten both wingbolts.
CAUTION: Handle porcelain enamel castings gen-
tly. The finish is fragile and can be easily dam-
aged. Place castings on a towel, carpet or other
protective surface.
tly. The finish is fragile and can be easily dam-
aged. Place castings on a towel, carpet or other
protective surface.
������
��������������������
����
��������������������
����
Stardance Rear
Vent
Vent
Grate
Screen
Top
Stardance
Top Vent
Top Vent
Left Side
Right Side
CAR207
Fig. 1 Carton contents for Stardance shell.
CAR208
Stardance
front options
6/07
Front
Stardance Front
w/Doors Package
w/Doors Package
Left Door
Right Door
CAR208
Fig. 2 Carton contents for operable door package.
2. Attach the right side to the rear skirt. (Fig. 4) Move
this assembly close to the stove’s final position. Align
the two sides at right angles to the back panel as
shown in Figure 5.
the two sides at right angles to the back panel as
shown in Figure 5.
NOTE: The firebox is shipped with three bolts and
spacers on the bottom to prevent any damage to
the bottom assembly. The two front bolts should be
removed after installation. Use a 7/16” wrench.
the bottom assembly. The two front bolts should be
removed after installation. Use a 7/16” wrench.