Enerco TSVFB10LP 사용자 설명서

Installation Instructions and Owner’s Manual

Unvented Liquid Propane Fired Room Heater

8.  Turn off heater (see To Turn OFF Gas to Appli-

ance, page 10. 

9.  Replace lower front panel. 

WARNING: If you do not follow these instructions 

exactly, a fire or explosion may result causing prop-

erty damage, personal injury or loss of life. 
A.  This appliance has a pilot that must be lighted 

by hand. When lighting the pilot, follow these 

instructions exactly.

B.  BEFORE LIGHTING smell all around the appli-

ance area for gas. Be sure to smell next to the 

floor because some gas is heavier than air and 

will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

• 

Do not try to light any appliance.

• 

Do not touch any electrical switch; do not use 

any phone in your building.

• 

Immediately call you gas supplier from a neigh-

bor’s phone. Follow the gas supplier’s instruc-

tions.

• 

If you can not reach your gas supplier, call the 

fire department.

•  Use only your hand to push in or turn the gas 

control knob. Never use tools. If knob will not 

push in or turn by hand, don’t try to repair it; call 

a qualified service technician or gas supplier. 

Force or attempted repair may result in a fire or 

explosion.

•  Do not use this appliance if any part has been 

underwater. Immediately call a qualified service 

technician to inspect the appliance and to re-

place any part of the control system which has 

been underwater.

1. 

STOP! Read the all safety information included 

with and on the side of heater.

2.  Check that gas supply to heater is on.
3.  Push in gas control knob and slightly turn clock-

wise to the OFF position (see figure 16).

Note: Knob cannot be turned from PILOT to OFF 

unless knob is pushed in slightly. Do not force.
4.  Wait five (5) minutes. Then smell for gas, in-

cluding near the floor. If you smell gas, 

STOP! 

Follow “B” in the safety information above. If 

you do not smell gas, go to the next step.

5.  Push in gas control know slightly and turn 

counterclockwise to PILOT/IGN and depress 

for five (5) seconds.

Note: The first time that the heater is operated after 

connecting the gas supply, the control knob should 

be depressed for about 30 seconds. This will allow 

air to bleed from the gas system.
6.  Push in control knob and rotate control knob 

back to OFF position then rotate counterclock-

wise to PILOT/IGN position. This will light pilot. 

If needed gently keep rotating control knob 

back and forth while depressed until pilot lights.

7.  Keep control knob depressed in for ten (10) 

seconds after lighting pilot. If pilot goes out, 

repeat steps 4, 5, 6 and 7.

 

If pilot does not stay lit, refer to Troubleshoot-

ing, pages 12-13. Also, contact a qualified 

service person or gas supplier for repairs. 

 

If control knob does not pop up when released, 

contact a qualified service person or gas sup-

plier for repairs.

8.   FOR IR10LP: Turn control knob to “LO” to light 

heater. Leave on “LO” position until the left 

burner tile has turned bright orange.

 

After left burner tile has turned bright orange, 

adjust heat output by turning Control Knob to 

desired position (“LO” or “HI”). Note: Both tiles 

turn orange only on HI setting.

FOR BF10LP: When the pilot is lit, turn the control 

knob to “HI” position to light.
FOR BF10LP: After flame is established on “HI”, 

adjust heat output by turning control knob to de-

sired position (“LO” or “HI”). Do not operate heater 

between locked positions.

CAUTION: Do not try to adjust heating level by using 

equipment shutoff valve. 

WARNING: When running heater, set control knob 

at “LO” or “HI” locked positions. Poor combustion 

and higher levels of carbon monoxide may result 

if heater is operated with control knob positioned 

between locked positions. 

IMPORTANT: Release downward pressure while turn-

ing control knob. Control knob must be locked at the 

desired position.

SHUTTING OFF HEATER:

1.  Turn off equipment shutoff valve.