Generac Power Systems H-100 사용자 설명서

The event log, as its name implies, is designed to 
store events which are programmable from GenLink. 
Each measurement channel or output function can 
be set as an event along with a setpoint. For example, 
if you set Digital Input #1 (the keyswitch in AUTO 
position) as an event with a setpoint of logical one, 
each time the keyswitch is set in the auto position, an 
event will be logged. Similarly you can set an analog 
event with an analog setpoint and a comparison type. 
For example you can set an event if the oil pressure 
is less than 10 psi or if power output is greater than 
100 kW.

Each event is recorded along with a time/date stamp 
and up to 6 optional measurements. The measure-
ments you want to record are selected from a pull 
down list in GenLink using the alarm/event log menu. 
They can be analog inputs, digital inputs or output 
functions. The event log can only be displayed via 
GenLink, it cannot be viewed on the front panel. 
Events are displayed by GenLink in chronological 
order, the most recent being at the top of the list.

The controller provides a mechanism to generate 
multiple warnings based on maintenance intervals. 
Normally it will be shipped with these warnings 
turned off. GenLink is used to enable these warn-
ings by setting a maintenance interval for the alarm 
of choice. The interval can be in engine run hours, 
a specific engine run hour, number of operations, a 
specific date or a combination of two of these meth-
ods. For example you can set the interval associated 
with oil life to 6 months or 100 engine hours (which-
ever occurs first). The transfer switch is one example 
of where a number of operations is relevant, spark 
plug life is not.

To disable a maintenance warning, set the “mainte-

nance cycle” field to N/A.

To set a specific date, set the “installed at” setting 

to the current date then set “End of life” to the 
specific date.

To set a number of operations, set the “installed at” 

setting to zero then set “End of life” to the number 
of operations required.

To set a specific operation number (say at opera-

tion 500), set the “installed at” setting to the cur-
rent number of operations, then set “End of life” to 
the operation number.

•

•

•

•

To set a number of engine run hours, set the 

“installed at” setting to zero then set “End of life” 
to the number of engine hours required.

NEVER set the “Installed at” hours to anything 

other than zero.

A warning is generated when the maintenance cri-
teria are met. This warning can be cancelled by the 
acknowledge button but will re-occur after 15 min-
utes. To permanently cancel the warning you must 
reset the maintenance interval. This can only be done 
via GenLink. The audible alarm will NOT sound for 
each 15 minute re-occurrence of the warning after 
the first maintenance warning is acknowledged.

The front panel display will show the percentage of 
life left for each possible maintenance item.

With the addition of an oxygen sensor and a solenoid 
to control the air fuel mix, the H-100 Control Panel 
can perform air/fuel ratio control to provide an opti-
mum (stochiometric) mix to reduce emissions. This 
feature can be turned on or off via GenLink. The air 
fuel solenoid output pin shares its function with the 
preheat output. You must choose one of the two func-
tions as follows:

To select air/fuel - set the “Diesel y/n” setting on the 

governor page to “No”. Set preheat to “No”

To select preheat - set the “Diesel y/n” setting on the 

governor page to “Y”. Set preheat to “Y”

Optionally the H-100 Control Panel can apply pre-
dictive firmware modeling to give I2T protection for 
the rotor and stator assembly. Based on parameters 
entered into the H-100 Control Panel via GenLink, 
the firmware models the temperature rise and fall 
of the alternator assembly and limits operation to 
prevent it being damaged. The entered parameters 
basically describe the thermal properties of each 
alternator to the firmware. GenLink allows you to 
choose the alternator model, and this automatically 
downloads the appropriate parameters. The H-100 
Control Panel will normally be delivered prepro-
grammed with the appropriate data . GenLink will 
allow you turn this feature on or off as desired. There 
is a GenLink display of the allowable temperature 
limits for the selected alternator (2 limits, one for the 
stator and one for the rotor) and also a display of the 
predicted temperatures.

•

•

•

•

 24