Beckett 150 사용자 설명서

 

Instruction Manual – 

Model AFII Oil Burner

Prepare before installing

 

      Denotes presence of a hazard which, if ignored, will result in 

severe personal injury, death, or substantial property damage. 

“HLX” heads 
Firing rate ..……..……………....…... 0.40 – 1.50 GPH 
Input ..………..….…………… 56,000 – 210,000 Btu/h 

“FBX” heads 
Firing rate ..…..……………………… 0.40 - 1.35 GPH 
Input ..………….…..………….56,000 – 189,000 Btu/h 

U. S. …. No. 1 or No. 2 heating oil only (ASTM D396) 
Canada ….... No. 1 stove oil or No. 2 furnace oil only 

Power supply ....…….... 120 VAC/60 Hz/single phase 
Operating load ……….… 5.8 Amps maximum; Note 1 
Motor …..……… ……………………..1/7 hp, 3450 rpm 
……….……...…… rotation CW when facing shaft end 
Ignition .……... Continuous duty iron-core transformer 
        OR ………..... Continuous duty solid state igniter 

Outlet pressure ………..…..……………………. Note 2 

ATC code ……………………….. See Table 1, page 2 

Dimensions  Height (maximum) ……….…….….…………13 inches 

Width (maximum) ………….………..….. …..14 inches 
Depth (chassis only) ………….……….6-11/16 inches 
Air tube diameter ………………………….3 ½  inches 

Note 1.  A burner with an electronic igniter will have a lower operating current.  
The actual load should be determined by a current meter. 
Note 2.  See appliance manufacturer’s burner specifications for 
recommended outlet pressure.  Pressure is 140 psig unless otherwise noted. 

      Denotes presence of a hazard which, if ignored, could result in 

severe personal injury, death, or substantial property damage. 

      Denotes presence of a hazard which, if ignored, could result in 

minor personal injury or property damage. 

      Intended to bring special attention to information, but not 

related to personal injury or property damage. 

•  Underwriters Laboratories  has certified this burner to comply with 

ANSI/UL 296 and has listed it for use with #1 or #2 fuel oil as specified in 
ASTM D396. Low sulfur #1 and #2 fuel oils reduce heat exchanger 
deposits with all burners compared to the standard fuels. Reduced 
deposits extend the service interval for cleaning and improve the 
efficiency of the appliance over time. Low sulfur fuels reduce 
particulate and oxides of nitrogen emissions as well. The Oilheat 
Manufacturers' Association recommends these fuels as the 
preferred fuels for this burner. 

•  State and local approvals are shown on burner rating label (see below). 
•  All oil burners should be installed in accordance with regulations of 

•  For recommended installation practice in Canada, refer to the latest 

version of CSA Standard B139.

 

 

     This equipment must be installed, adjusted and started only 

by a qualified service agency – an individual or agency, licensed and 
experienced with all codes and ordinances, who is responsible for the 
installation and adjustment of the equipment. The installation must comply 
with all local codes and ordinances and with the latest revision of the National 

Fire Protection Standard for Oil-Burning Equipment, NFPA 31 (or CSA B139). 

 
 

 

     Read all instructions before proceeding. Follow all 

instructions completely. Failure to follow these instructions could result in 
equipment malfunction, causing severe personal injury, death or substantial 

property damage. 

 
 
 
 

 

     Concealed damage — If you discover damage to the burner 

or controls during unpacking, notify the carrier at once and file the appropriate 

claim. 

 
 
 

 

        When contacting Beckett for service information — Please 

record the burner serial number (and have available when calling or writing). 
You will find the serial number on the silver label located on the top right of the 
burner, to the left of the air dial. See illustration below. 

 
 
 

 

 
 
 
 
 
 
 
 
 
 

SK9642