Sony RM-V111T 전단

3-230-683-11(2)

Remote Commander

Sony Corporation © 2001  

Printed in Malaysia

You can set up this Remote Commander to operate the following
components of almost all major brands including Sony.

TV

VCR

Sony TV

Sony VHS VCR (VTR3)

Open the battery compartment and insert two R6 (size AA) batteries
(not supplied).
Be sure to line up the + and – on the batteries with the + and – on the
battery compartment.

Under normal conditions, batteries will last up to six months. If the
Remote Commander does not operate properly, the batteries might
be worn out. Replace the batteries with new ones.

Notes
• Replace both batteries with new ones.
• Do not take more than 20 minutes to replace the batteries; otherwise, your

setting of the code numbers will be erased.

• Do not mix old batteries with new ones or mix different types of

batteries together.

• If the electrolyte inside the battery should leak, wipe the

contaminated area of the battery compartment with a cloth and
replace the old batteries with new ones. To prevent the electrolyte
from leaking, remove the batteries when you plan not to use the
Commander for a long period of time.

To use this Remote Commander with a Sony brand component that
is already preset at the factory (see the table on the left), you can skip
this procedure.
If you are using other brand’s component or if you cannot operate
even a Sony brand component, follow this procedure.

See the supplied “Component Code Numbers” and find the code for
your component.

Enter the three-digit component code in the “Component
Code Numbers” table.
For example, to set a Philips’ TV, press -86.

Press the t button.

Go through the same procedure for each component you want to set
up.

• First, try repeating these set up procedures using the other codes

listed for your component (see “Component Code Numbers”).

• If — after trying all the codes listed for your component — you still

cannot get the Commander to work properly, try the search
method described under “Setting by Searching for the Correct
Code”.

Note
Be sure to proceed to each next step in the above procedure within 10 seconds;
otherwise, the setting mode will be canceled.

Tip
You can write down the code number on the label inside the battery
compartment lid.

If you’ve tried all the code numbers listed for your component and
you still cannot get the Commander to work (or if your component
was not listed), try the following.

Turn on the component you wish to set up using its power
switch.

Press the S (Set) button.

Press the button of the component that you want to set up.

Aim the Commander to your component, and press and release
the PROGR+ button. Then press and release the 1 button.

Repeat step 4 until the correct code number is found.
Each time you press the PROGR+ button and then the 1 button, a
new code number will be transmitted.
Keep trying until your component operates as follows:
• TV, VCR or satellite tuner : the power turns off.
• TV without a power switch: the Channel + function works.

Be patient as you do this; it may take up to about 120 tries for a
TV, and about 60 tries for VCR until the correct code number is
located.

When the correct code is found, press the t button.

Turn on the component again, and check that the Commander
can control the other functions of your component such as
channel and volume control.

If the component does not operate properly, repeat steps 2 to 6 and
search for another code.

If you still cannot get the Commander to work properly, see
“Troubleshooting”.

Note
Be sure to proceed to each next step in the above procedure within 10 seconds;
otherwise setting mode will be canceled.

Point the Commander directly to your component and press
the button for the desired function.
See “Remote Button Descriptions” for details.

Notes on using the Commander
• Using this Commander will not add new functions to your components.  The

functions of the Commander are limited to the functions of the component
itself. For example, if your TV does not have a mute function, the % button
on this Commander will not function with your TV.

• Do not forcibly remove or tear off the corner protector.

If you’re having problems setting up or using the Remote
Commander:
• When setting up the Commander, carefully go through the

procedures described under “Setting the Component Codes”. If the
code that’s listed first for your component doesn’t work, try all the
codes for your component — in the order in which they’re listed. If
all the codes fail to work (or if your component is not listed), try
using the procedures under “Setting by Searching for the Correct
Code”.

• Check that you’re aiming the Commander directly at the

component, and that there are no obstructions between the
Commander and the component.

• Make sure the batteries you’re using are not worn out, and that

they’re inserted correctly.

• Check that the button of the TV or VCR is pressed to choose your

desired component.

• Check that the component has infrared remote capability.  For

example, if your component didn’t come with a remote control, it
probably isn’t capable of being controlled by the Remote
Commander.

• Should any problem persist, reset the Commander to the factory

setting by pressing the 1, t and 2– buttons simultaneously.

If you have any questions or problems concerning the Remote
Commander that are not covered in this manual, please call the
telephone number in the warranty.

Approx. 7 m (23 ft) (varies depending on the component of each
manufacturer)

Two R6 (size AA) batteries (not supplied)

Approx. 6 months (varies depending on frequency of use)

Approx. 51.8 

×

 195 

×

 31 mm (w/h/d) (2 

1

/

8

 

×

 7 

3

/

4

 

×

 1 

1

/

4

 in.)

Approx. 100 g (3.5 oz.) (not including batteries)

Design and specifications are subject to change without notice.

1 To set up the Commander.
2 Component select buttons. To

switch to the operations of each
component, press the button on
which that component is
assigned.

8 Volume up: +

Volume down: –

9 To mute the volume on TV.
0 To turn on and off the power of

the selected component.

3

TV: To change the input mode.
VCR: To switch the signals
supplied to the TV.

4

TV: To switch to Teletext.
VCR: To expose the on-screen
display.

5

TV/VCR: To select double-digit
numbers. Works in the same
way as your TV’s commander
or VCR’s commander.

6 and 7

TV: N, x, m, M :
Fastext buttons.
VCR: N: To play.

x

: To stop.

m

: To rewind.

M

: To fast-forward.

z

REC: To record,

press N while
pressing z.

qa

TV: To turn on.
To return from Teletext to TV.
VCR: To change the input
mode.

qs To change the programme.

Also to turn on the power.

qd

TV/VCR: To select a number
between 20 and 29.

qf Programme up: +

Programme down: –

qg To operate JUMP, FLASHBACK

or CHANNEL RETURN function
on the TV depending on the
setting of the TV’s
manufacturer.

1

2

3

4

9

8

7

5

6

0

qa

qs

qd

qf

qg